Favorites 
No products with active filter could be found, showing all.
These perforated columns are used for attachment to the back edge of pack and work tables, for use with our extensive range of accessories. The pillars are delivered in pairs and consist of 2 profiles of 25x50x2 mm. The net height above the table top is approximately 400 mm less than the height of the column, (depends on the thickness of the table top). The mounting kit must be ordered separately. NOTE 1 set per column, i.e. 2 mounting kits for this article. For increased stability in the superstructure, you can use intermediate braces for the desired CC dimensions.
Choose between the different lengths of perforated columns depending on what you have in mind for the extensions and assessors you want.
Rail for mounting between perforated columns. The rail can be mounted between vertical columns at the back edge of the work table – this gives better stability to the superstructure. For the construction of floor-standing L and T foot systems, these intermediate braces must be used so that the stands have the necessary stability. Choose the intermediate brace that corresponds to other equipment that you want to use – whether it’s shelves, tool boards, tool cabinets or other workplace furnishings.
The set is used for mounting perforated columns on a superstructure frame.
The mounting kit consists of two spring-loaded 4-point nuts, two screws and two washers.
One set is needed per pillar.
Trolley with 4 ball-bearing wheels and carabiner hook, for use in c-profile rail together with Balance block for mobile suspension of tools or other assembly equipment. If you wish to limit the movement of the running cart, you order end stops in addition.
Balance block for tools and assembly equipment. The balance blocks have an easy adjustment for different loads, the durable polyamide line has a working range of 2.0 m and elastic line stop.
Mounting bracket for mounting c-profile rail in fixed arms. 1 mounting bracket is included for each fixed arm, but these can be additionally ordered if you want several c-profile rails mounted – or if there is other equipment to be mounted in the work table’s superstructure. The mounting bracket is adjustable to a certain extent and is basically designed for use with profiles that are 30 x 32 mm.
Solid 600 mm LED work lighting with dimmer for optimal work lighting. The lamps are produced in aluminum and can be angled.
Supplied complete with mounting hardware and 3 m cable and for mounting in a fixed arm for side mounting on the right of the work table.
LED lighting, 19 w with dimming via spring-loaded push button with memory suitable for workplaces that require a high light flux. Angled for the desired direction of light. Fits most workplaces from heavy industry such as lab environments or why not on a packing table.
Complete LED work lighting for installation in our vertical perforated columns. The depth of the fixture is 640 mm from the perforated column. The workplace lighting has integrated LED lights that provide a combination of side and longitudinal light. Supplied complete with arm and bracket and cable with plug. Connects to 230 V – 50Hz. RAL 9006.
A complete longitudinal LED lighting with lighting ramp at the front, integrated LED lights that are adjusted laterally using the magnetic strip. Fits all our tables with extensions, delivered complete.
Complete busbar for horizontal placement in our perforated columns, C7C 670/900/1340/1800 mm.
The power rail is delivered with 6 grounded contacts, illuminated switch and 3 m cable with grounded plug.
Connects to 230 V – 50 Hz. Designed for use in Norway, Sweden, Denmark and Finland.
Complete power rail, suitable for all tables with extensions, available in all our standard dimensions. A stylish and safe power source as well as keeping the cords you use for your table in order.
Energy panel that is mounted vertically in one of our pillars. The panel has 4 sockets with switches that light up when the power is on. 3 m cable included.
Energy panel that fits all our tables that have a perforated column. Simple assembly and you have control over the cords you use for your table.
Practical perm holder with space for 2 A4 perms, for external mounting on pillars.
Combined flat screen and keyboard holder, where the fully adjustable screen holder is adapted for screens with VESA 75/100 and the keyboard holder includes a pull-out mouse table. The capacity is 15 kg distributed load.
The screen and keyboard holder is mounted on the included articulated arm, which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Shelf with dimensions h x w x d = 120 x 545 x 170 mm for placing picking boxes, designed for optimal placement of 5 of our 2075 boxes.
The pull-out box shelf is mounted on the included articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Articulated shelf on arm for placing picking boxes, provides a better, ergonomic and more efficient workplace.
This arm has 3 joints, which makes it very flexible. The length of the arm is 570 mm including column attachment, and can be used as a starting point for attaching shelves, tool holders, boards or the like. At the end of the arm there is a through hole for an M8 screw, the height of the attachment is 99 mm and the distance from the center to the outside is 15 mm (excl. end plug).
Double suspension strip for pick and store boxes, optimal for use with our 2075 boxes. This double slat for pick boxes is mounted on the supplied articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace. Maximum load distributed weight 15 kg.
Adjustable document holder with h x w = 330 x 290 mm, for the use of upright A4 sheets and documents and with a capacity of 15 kg distributed load.
The document holder is mounted on the accompanying articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Articulating arm with fully rotatable keyboard holder and mouse pad. The articulated flatscreen holder is mounted on perforated pillars. The mouse pad can be mounted on the left or right side. The plate for the mouse pad is white.
Screen holder with fully rotatable universal mount for screens with VESA 75/100 mounting. The capacity is 15 kg distributed load. The screen holder is mounted on the accompanying articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Adjustable shelf with w x d = 405 x 305 mm, winding edge around the entire shelf and capacity 15 kg distributed load. The tiltable shelf is mounted on the accompanying articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Shelf complete with mouse holder, brackets and fasteners. The shelf has expansions, which provide 100% extendability. Mouse pad made of plywood is primed with clear lacquer. The mouse pad, which is white, can be pulled out on the right or left side. The pull-out keyboard shelf can be used on all work tables in our range.
Dimensions: Shelf, 565 x 470 x 95 mm.
Dimensions: Mouse pad, 565 x 210 x 9 mm.
Tool panel perforated with 9 mm square hole with CC 38 mm and articulated arm.
Used together with tool hooks for hanging smaller hand tools. The capacity is 15 kg distributed load.
Cable channel placed on the side of perforated columns, fixed with column end plugs. Cables are pulled in a U-profile 30 x 30 mm, the cable channel has 9 penetration openings evenly distributed over the total length of 1926 mm.
Perforated tool panel with 9mm square hole with cc measure 38mm.
With the included mounting kit, the board is easily mounted on columns on work tables, on wall rails or on mounting trolleys.
The panel can also be mounted right on the wall.
Hook set tool hooks mixed 24-pack.
Hook set 24-pack contains:
Suspension hook 35-711- 5 pcs
Suspension hook 35-715- 2 pcs
Double hook 35-721- 6 pcs
Double hook 35-724- 2 pcs
Bar hook 35-755- 2 pcs
Angle hook 35-750- 3 pcs
Drawer holder with storage tray 41-803- 1 pc
Pipe holder 42-086- 1 pack (2 pcs. Ø 25-22 mm + 1 pc. Ø 37-34 mm, height 75 mm)
Complete with tool board (not included), which i.a. available for mounting directly on a wall, at a work table, in a cabinet or on trolleys. The hooks are hooked into the perforation of the tool board and locked with a stop screw.
The hooks fit GBP’s tool boards, which have a hole dimension of 9 mm (4-edge hole) and hole spacing of 38 mm.
Magnetic whiteboard for placement in perforated columns at the back edge of work and packing tables, on floor-mounted L and T stands, on assembly trolleys or directly on the wall.
Necessary mounting details for mounting on the column are included.
Practical whiteboard, write on it or put magnets on it, the areas of use are many. Available in different CC measurements for our different products.
Suspension rail for use with storage boxes or modular boxes.
The rail has integrated brackets for straight or angled mounting on our perforated columns. The capacity is 20 kg distributed load. Plastic boxes are not included and must be ordered separately – See related products for the most common plastic boxes used with the suspension rail.
Arm with a length of 700 mm, for mounting in our perforated columns. This fixed arm is used together with one or more c-profile rails, for hanging mobile tool holders, work lighting or other mounting material. 1 bracket for c-profile is included, if you want more c-profiles, you order several brackets, 1 per arm / 2 per c-profile.
Shelf with jump plane capacity 50kg distributed load. The storage shelf is delivered with 2 brackets / brackets and is intended for mounting in our perforated columns, at the back edge of work and packing tables, on floor-mounted L- and T-stands or on our assembly trolleys.
The storage shelf is reversible, has a completely flat side and a side with 4 ridged edges and can be placed horizontally or at an angle.
C-profile rails for mounting work lighting, mobile tool holders or other mounting equipment. The C-profile rail was attached over the work table in a fixed arm with a length of 700 mm.
End stop, consisting of a square washer (25x30x5 mm) with screw and washer for placement in the suspension C-profile.
Lighting set consisting of 1 C-profile L-1490 mm, 2 fixed arms L-700 mm and light fitting LED 38W.
Solid LED work lighting with dimmer for optimal work lighting. The lamps are produced in aluminum and can be angled.
Lockable desk drawer with expansions that provide 100% extendability.
The box is mounted in the table stand using suspension profiles or screwed directly into a heavy (40 mm thick) table top.
Inside box dimensions: W300 x D460 mm.
The suspension profiles are ordered separately. Complete with drawer interior in gray sheet steel or red plastic.
Lockable desk drawer with expansions that provide 100% extendability.
The box is mounted in the Lätt H table stand using suspension profiles or screwed directly into a heavy (40 mm thick) table top.
Inside box dimensions: W450 x D605 mm.
The suspension profiles are ordered separately.
Drill holder with space for 32 different drills. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Hook Box holder for hanging a plastic box. Available as holder only but also incl. box.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Document clip 60 mm. Supplied in 1-pack.
Ring key holder is a vertical ring key holder for eight ring keys. Galvanized. Sell 1 pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
The storage case is mounted in the table stand using suspension profiles that are ordered separately. Hurtsen can also be screwed directly into a heavy table top (40 mm).
Does not fit when lower shelf is used.
The storage case fits all tables in the wide range. The desk section can be locked with a central lock.
The Hurtsars are equipped with ball-bearing expansions, which provide 100% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order inside the drawers. Drawer division, number x height (mm): 3×100. Maximum load distributed weight: 100 kg.
The storage basket is used freestanding, with or without a wheel base.
The Hurtsen can be locked with a central lock. Box division, number x height (mm): 1×50 + 3×100 + 1×150.
The Hurtsars are equipped with ball-bearing expansions, which provide 100% extensibility.
Maximum load distributed weight for Hurts: 100 kg.
Complete with interior decoration for the drawers to create order and order inside the drawers.
The wheel base is ordered separately.
Wheel set adapted for use with our lightweight work tables. The set consists of 4 swiveling Ø100 mm rubber wheels, 2 of which are lockable, and with reinforced foot sleeves.
Wheel set adapted for use on our heavy leg stands / industrial tables. The set consists of 4 swiveling Ø125 mm rubber wheels, 2 of which are lockable, as well as reinforced foot sleeves. The capacity is 70 kg / wheel, a total of 280 kg.
Wheel set for work tables ErgoMini 2 and ErgoNomi is complete and consists of 4 double wheels, lockable castors with Ø75mm diam. Height 99 mm, bolt diameter 10 mm.
Wheel set for work table ErgoMulti 2 and Bord 400 is complete and consists of 4 double wheels, lockable castors with Ø75mm diam. Height 99 mm, bolt diameter 10 mm.
A complete set of wheels for one or two-post tilting tables ErgoTilt. The set consists of 4 castors with total brake and rubber track, diameter 160 mm. The wheels are mounted on a steel tube adapter. The wheel set raises the tilting table 40 mm.
Shelf is provided with hooks, which fit the perforation in the panel. Galvanized. 1 pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Shelf divider for use as a binder support, side support or other type of demarcation.
The compartments are delivered in 2-packs and are adapted for shelves with a depth of 300mm.
Use the divider for e.g. binders, books or as a cardboard support, our dividers can be used for most things, give a structured impression, order and order!
Cup for e.g. spray cans and small gadgets. Galvanized. The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw. The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm. The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Hook set tool hooks mixed 20-pack
Hook set 20-pack contains:
Suspension hook 35-713- 4 pcs
Single hook 35-731- 6 pcs
Spring clamp 35-766- 3 pcs
Spring clamp 35-767- 3 pcs
Double hook 35-722- 4 pcs
Hook set tool hooks mixed 56-pack
Hook set 56-pack contains:
Suspension hook 35-711- 20 pcs
Double hook 35-721- 10 pcs
Bar hook 35-755- 5 pcs
Angle hook 35-750- 5 pcs
Ring hook 35-760- 1 pc
Ring hook 35-761- 1 pc
Spring clip 42-464- 10 pcs
Pipe holder 42-086 1 pack
Cup 35-780- 1 pc
Complete with tool board (not included), which i.a. available for mounting directly on a wall, at a work table, in a cabinet or on trolleys. 42-464-0001 replaces part number 41-962-0001.
The hooks are hooked into the perforation of the tool board and locked with a stop screw.
The hooks fit GBP’s tool boards, which have a hole dimension of 9 mm (4-edge hole) and hole spacing of 38 mm.
Joint spanner holder for five joint spanners. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
The kit is used for mounting perforated columns on the spacer box for ErgoMulti
The assembly kit consists of reinforcement angle incl. required screws and assembly instructions.
One kit is needed per pillar. Reinforcement angle is only used when mounting a perforated column placed in the middle of the width of the table. Color: silver, RAL 9006
Tool hook Key holder with space for 12 keys in varying sizes. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Superstructure frame intended for work tables ErgoMini and ErgoNomi.
With the help of the extension frame, you can mount GBP’s large extension range. Complete with Perforated pillars and Mounting kit for Perforated pillars, which are mounted on the superstructure frame.
Then continue with accessories such as suspension strips with plastic backs, tool boards and tool hooks, shelves, cutting units or lighting, so that the work table is optimal. Hurtsar can be mounted under the table top. With work tables and other workplace furniture from GBP Ergonomics, we guarantee quality, safety and constant development.
Our products improve both efficiency and ergonomics at your workplace. Feel free to contact us if you have questions about work tables or other workplace equipment.
Add-on frame intended for workbench.
Add-on frame intended for ErgoSingle Workstation. The frame is adapted for c/c 670 mm. With the add-on frame, the ErgoSingle can easily be supplemented with more add-on details.
Extension kit adapted for c/c 670 mm.
The extension kit includes:
2 perforated columns 2000 mm, shelf and suspension strip for plastic trays.
Complete the suspension strip with plastic trays for smart and practical storage.
Basic add-on set for work and packing table with perforated columns 1446 mm, intermediate brace and mounting kit. Fits ErgoMulti.
Pipe holder, supplied in 2-packs.
Tool hook Hose shelf for hanging various. cables and hoses, etc. Galvanized. 1 pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Sockelplåt för fristående verkstadshurts. Sockelplåten behövs för höjdjustering av fristående hurts, när den används tillsammans med Fast Arbetsbänk / Tung benbock. Säljs i 2-pack.
Hållare för sprayburkshållare eller liknande. Förzinkad.
Verktygskroken passar perforerade paneler, där den hakas i plåtens perforering och låses med stoppskruv.
Den perforerade panelen (verktygstavlan) har håldimension 9 mm (4-kantshål) och hålavstånd 38 mm.
rokarna passar samtliga perforerade paneler, oavsett om de är monterade i skåp, vagnar eller på arbetsbord.
This pivoting arm has a length of 700 mm and is supplied with 1 eye hook for hanging tools and other mounting equipment. The arm is mounted in our perforated columns, can be swiveled 180 degrees and has a capacity of 10 kg distributed load.
Tool hook wire shelf 385x180x100 mm. Powder coated in RAL 9006. Supplied in 1-pack
HPL undershelf in 24 mm thickness, adapted for work tables with H-stand base and with depth 800 mm and width 1500/2000 mm.
Bottom shelf in 40mm thickness, adapted for work tables with heavy leg braces and depth 800mm / width 1200/1500/2000mm.
Steel shelf with a depth of 350 mm, for installation under a workshop bench with a width of 1200/1500/2000 mm. Maximum load is 100 kg. Powder coated in gray RAL 7004.
Bottom shelf for ErgoMini/ErgoNomi with a width of 2000 mm, is a 24 mm tabletop with a top surface in gray high pressure laminate (HPL) edged with dark gray ABS edging. The capacity is 50 kg distributed load. The lower shelf is delivered complete and brackets for attachment to the ErgoMini/ErgoNomi underframe are included.
Perforated tool bar with 9mm square hole with cc measure 38mm. With the supplied mounting kit, the strip is easily mounted on columns on work tables, on wall rails or on assembly trolleys.
Smooth perforated tool bar, a good help for order and order. Complement the perforated strip with GBP’s wide range of hooks, which consists of around 50 hooks for different purposes.
Suspension rail with a width of 900 mm, for use together with storage boxes or modular boxes. The rail has integrated brackets for straight or angled mounting on our perforated columns. The capacity is 20 kg distributed load. Plastic boxes are not included and must be ordered separately – See related products for the most common plastic boxes used with the suspension rail.
The workshop desk drawer is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top. Complete the hurt with the top plane when used as a free-standing hurt. Lockable with central lock. Built-in safety means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility. Complete with interior decoration for the drawers in gray sheet steel or red plastic to create order and order. Box division, number x height (mm): 1×50 + 1×100 + 3×150. Maximum load distributed weight: 175 kg.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Complete the drawer section with the top plan, when used as a stand-alone hurt. Lockable with central lock.
Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility. Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order.
Drawer division, number x height (mm): 1×50 + 1×100 + 1×150 + 1×300. Maximum load distributed weight for drawer section: 175 kg.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top. Complete the desk drawer section with the top plane when used as a free-standing hurt. Lockable with central lock. Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility. Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order. Box division, number x height (mm): 1×50 + 2×100 + 1×150 + 1×200. Maximum load distributed weight for desk drawer section: 175 kg.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Complete the hurt with top plan when used as a free-standing hurt. Lockable with central lock.
Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order.
Drawer division, number x height (mm): 6×100. Maximum load distributed weight for: 175 kg.
The workshop desk is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top. Complete the hurt with the top plane when used as a free-standing desk. The desk has a door with dimensions W470 x H630 mm. A shelf is included with the kit. The desk is lockable.
Brace hook for various pliers or similar gripping tools. Galvanized. The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw. The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm. Delivered in 3-packs.
Single hook for hanging e.g. hand tools. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Sold in packs of 5 and available in lengths of 10 mm or 50 mm.
Spring clamp Ø6, 12, 18 and 25 mm for hanging e.g. screwdrivers or similar small hand tools. Supplied in 5-packs.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Galvanized packaging hook is adapted for hanging different packages with riders. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Socket holder for five sockets. Galvanized. The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The box holder is adapted for hanging small storage boxes/plastic trays. Complete with plastic backing from GBP. The holder is galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Galvanized hook for hanging spanners. Comes in 5-packs.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Galvanized ring hook. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Ring key strip, with space for seven ring keys, which can also be used as a sleeve holder. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Roll holder adapted for hanging different rolls. Supplied in 1-pack.
Round hook for hanging hand tools and smaller hand machines. Galvanized. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Screwdriver holder.
Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Closed double hook for hanging e.g. small hand tools. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Double hook for hanging e.g. hammer or similar impact tool. Galvanized.
Available in different sizes, see article number below.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Double hook for hanging e.g. hammer or similar impact tool. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Galvanized single hook for hanging e.g. hand tools. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Double hook adapted for hanging hammers and similar impact tools. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Galvanized single hook at a 30° angle, for hanging e.g. hand tools. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Single hook at a 30° angle, for hanging e.g. hand tools. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Tool cabinets for placement directly on the wall or in perforated columns (CC 900), at the back edge of work and packing tables, on floor-mounted L- and T-stands, on assembly trolleys. Necessary mounting details for mounting on the column are included.
The tool cabinet is perforated (9mm square hole with CC 38mm) so you can use our tool hooks for efficient storage of tools.
Wheel set for work table ErgoMulti and Bord 400 is complete and consists of 4 double wheels, lockable castors with Ø75mm diam. Height 99 mm, bolt diameter 10 mm.