Favorites 
No products with active filter could be found, showing all.
24 mm table top for work tables. The tabletop has a light gray high-pressure laminate (HPL) top edged with a dark gray ABS edging strip.
The HPL surface provides a table top with high scratch resistance and which is resistant to liquids and chemicals.
The tabletop is adapted to be used together with Light H-, ErgoMini, ErgoNomi, Bord 400 and ErgoMulti undercarriage.
Feet that combine with perforated columns for construction of floor-saving racks. The L or T foot is combined with columns of the desired height and 2 intermediate braces for the desired width. Capacity is 100 kg for L-foot and 150 kg for T-foot, with evenly distributed load.
These perforated columns are used for attachment to the back edge of pack and work tables, for use with our extensive range of accessories. The pillars are delivered in pairs and consist of 2 profiles of 25x50x2 mm. The net height above the table top is approximately 400 mm less than the height of the column, (depends on the thickness of the table top). The mounting kit must be ordered separately. NOTE 1 set per column, i.e. 2 mounting kits for this article. For increased stability in the superstructure, you can use intermediate braces for the desired CC dimensions.
Choose between the different lengths of perforated columns depending on what you have in mind for the extensions and assessors you want.
Complete electrically adjustable ESD work table Table 400 with 24mm table top in gray soft mat in ESD design or laminate.
The table top has solid wooden edging and grounding terminal on the underside. The table is supplied with a grounding terminal with push buttons intended for ESD wristbands, a grounding contact with ring cable lug and a terminal block.
The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded. The table is equipped with a stable intermediate brace.
Easy floor stand on L-foot. Bass section consists of: A set of two columns with welded-on L-foot Two intermediate braces with a width of 875 mm Additional section consists of a column with a welded-on L-foot and 2 intermediate braces. Floor stand base section can be placed alone or assembled together with additional section to full lengths.
Complements can only be mounted on the front of the single stand.
Table stand for the electrically adjustable Bord 400, for 24mm table tops. The maximum capacity refers to distributed load.
The lifting speed applies without load and the working height is without table top. Control box and standard hand controller TH14 included, 24 mm table top ordered separately. The table is equipped with a stable intermediate brace.
Bord 400 is designed to meet the needs of industry. Ergonomics and productivity are the basis for the construction of the stand.
Bord 400 is very flexible and can be easily adapted to specific needs and tasks. The table enables a wide range of accessories and the latest technology in terms of electronics has of course been used in this table stand.
See table tops and add-on details below.
Read more about how to build your workbench here.
Rail for mounting between perforated columns. The rail can be mounted between vertical columns at the back edge of the work table – this gives better stability to the superstructure. For the construction of floor-standing L and T foot systems, these intermediate braces must be used so that the stands have the necessary stability. Choose the intermediate brace that corresponds to other equipment that you want to use – whether it’s shelves, tool boards, tool cabinets or other workplace furnishings.
Perforated tool board for wall mounting. The board is perforated with square holes of 9 x 9 mm and with a hole distance of 38 mm.
Complete the tool board with our wide range of hooks, which consists of around 50 hooks for various purposes.
Table stand for the electrically adjustable Work Table ErgoMini, for 24mm table tops.
The maximum capacity refers to distributed load. The lifting speed applies without load and the working height is without table top.
Control box and standard table control are included, but 24 mm table top and possible add-on frame are ordered separately.
See table tops and add-on details below.
Read more about how to build your workbench here.
Electric work table ErgoMulti, for 24 mm table top. The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded. The stroke length of 450 mm provides an optimal working height.
See table tops and add-on details below.
Read more about how to build your workbench here.
Table stand for the crank table ErgoNomi, for 24mm table tops. The maximum capacity refers to distributed load. The working height is without a table top. Table top and possible extension frame are ordered separately.
See table tops and add-on details below.
Read more about how to build your workbench here.
Table stand for work table Lightweight work table, to be used together with 24 mm table tops.
Table stand is delivered complete (without table top) and consists of 2 pairs of square legs, frame for relieving the table top and extension frame for hanging accessories at the back of the table.
Table stand is manually adjustable, table top ordered separately. With the accessory wheel set, the working height is 835 – 1075 mm. The maximum capacity refers to distributed load.
See table tops and add-on details below.
Read more about how to build your workbench here.
Manually adjustable and very stable leg braces for use with our 40mm table tops.
The leg stands are delivered individually and have a capacity of 500 kg distributed load (300 kg. with wheels). Working height 700 – 970 mm without table top. For table tops with a width of 2500 mm, the use of 3 leg brackets is recommended.
See table tops and add-on details below.
Read more about how to build your workbench here.
Electrically adjustable work table consisting of Bord 400 with 24 mm gray high-pressure laminate board or vinyl board. The table’s maximum load of 400 kg applies with a spread load, lifting speed applies when the table is unloaded. The table is equipped with a stable intermediate brace.
See related add-on details below.
Read more about how to build your workbench here.
Complete electrically adjustable work table ErgoMini including 24 mm gray high pressure laminate table top or vinyl table top. The table’s maximum load of 180 kg applies with a spread load, lifting speed applies when the table is unloaded.
The stroke length of 450 mm provides an optimal working height, including the table top.
ErgoMini is an electrically adjustable work table that consists of two table legs with integrated motors in each leg.
The stand has intermediate braces for increased stability. The table height is easily regulated with a table control, which is mounted under the top in the table frame.
ErgoMini delivered complete with extension frame.
See related add-on details below.
Read more about how to build your workbench here.
Boltless Universal shelf Starter section, with shelf height 2000 mm, beam width 1500 mm and shelf depth 400 mm.
The universal shelf has 3 shelves in height, with a total capacity of 1200 kg.
The universal shelves help you make maximum use of the space and the shelves are adjustable and fit in stores, regardless of size.
Complete manually adjustable ESD work table Light H with 24 mm table top.
The table top with gray soft carpet (linoleum) or laminate in ESD design, solid wooden edging and grounding terminal on the underside, with a depth of 800 mm.
The table is supplied with a grounding terminal with push buttons intended for ESD wristbands, a grounding contact with ring cable lug and a terminal block. The load capacity applies with a spread load.
Floor rack easily on T-foot. Bass section consists of: A set of two columns with a T-foot welded on Two intermediate braces with a width of 875 mm Additional section consists of a column with welded T-foot and 2 intermediate braces. Floor stand base section can be placed alone or assembled together with additional section to full lengths.
Complements can only be mounted on both the front and back of the floor stand.
Complete electric work table ErgoMulti, including 24mm gray table top in high-pressure laminate or vinyl.
The laminate surface provides a tabletop with high scratch resistance and which is resistant to liquids and chemicals.
Vinyl is an all-round record for e.g. packing and assembly work, but with limited resistance to solvents.
The table’s maximum load of 250 kg applies with a spread load, lifting speed applies when the table is unloaded. The stroke length of 450 mm provides an optimal working height.
The undercarriage is delivered complete with combined cable protection / extension frame adapted to our wide range of accessories.
See related add-on details below.
Read more about how to build your workbench here.
ErgoNomi is a table that can be raised and lowered. The stand has intermediate braces for increased stability.
The table height is easily adjusted with the crank. Including 24 mm gray table top in high-pressure laminate.
The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded. The stroke length of 450 mm provides an optimal working height.
See related add-on details below.
Read more about how to build your workbench here.
Complete manual adjustable work table lightweight H-stand with 24 mm table top with gray high pressure laminate or gray vinyl.
Maximum load is 150 kg distributed weight, working height incl. disc 724-974 mm.
The load capacity applies with a spread load. With the accessory wheel set, the height increases by 135 mm.
Feel free to complete with a storage box placed under the table.
See related add-on details below.
Read more about how to build your workbench here.
Workbench with adjustable leg brackets, 40 mm laminate table top or vinyl top.
The capacity is 750 kg distributed load and the working height is 740 – 1010 mm.
This is a very stable work table that you can manually adjust in height for the best ergonomics.
The table is available in several designs, sizes and with various different add-on details and accessories to meet your specific needs.
See related add-on details below.
Read more about how to build your workbench here.
Please contact our customer service if you would like more information or advice.
ASPB model 1 is a complete back cabinet, consisting of the fully welded ASHV steel cabinet with doors in anthracite, blue or light grey, in combination with the necessary number of shelves and 36 blue storage backs with d x w x h = 400 x 230 x 150 mm.
ASPB model 1 is a complete back cabinet, consisting of the fully welded ASHV steel cabinet with doors in anthracite, blue or light grey, in combination with the necessary number of shelves and 45 blue storage backs with d x w x h = 400 x 230 x 150 mm.
Electrically adjustable work table equipped with Table 400 with 24 mm gray high-pressure laminate board. The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded. The table is equipped with a stable intermediate brace.
Floor stand Comb. 1 consists of 1 double rack base section, 1 double rack extension section, 4 intermediate braces, 2 tool boards, 3 suspension strips and 18 blue backs (4 pcs 3067, 6 pcs 3074 and 8 pcs 3075)
Workshop and Workshop cabinet GBP fully equipped with interior.
The cabinet contains:
1 drawer compartment
1 shelf with telescopic rails
1 fixed reinforced shelf
1 box with telescopic rails
1 perforated tool board inside door
1 pair of perforated tool boards cabinet end
1 backlist
1 hook set 24-pack
7 storage boxes 96x105x45
Complete electrically adjustable ESD work table ErgoMini including extension frame and 24 mm gray ESD laminate table top or ESD mat.
The tabletop has a solid wooden edging and grounding terminal on the underside. The table is supplied with a grounding terminal with push buttons intended for ESD wristbands, a grounding contact with ring cable shoe and a terminal block.
The load capacity applies with a spread load and lifting speed applies with an unloaded table. The stroke length of 450 mm provides an optimal working height.
Complete electrically adjustable work table ErgoMini including 24 mm gray high-pressure laminate on table top.
The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded. The stroke length of 450 mm provides an optimal working height, including the table top made of high-pressure laminate.
ErgoMini is an electrically adjustable work table that consists of two table legs with integrated motors in each leg. The stand has intermediate braces for increased stability. The table height is easily regulated with a table control, which is mounted under the top in the table frame.
The stand is prepared for an extension frame, which is ordered separately.
Floor stand Comb. 2 consists of: 1 double rack base section, 1 double rack extension section, 4 intermediate braces, 2 tool boards, 1 whiteboard, 3 suspension strips and 18 blue backs (4 pcs 3067, 6 pcs 3074 and 8 pcs 3075)
Workshop cabinet Package 1 is a stable fully welded tool cabinet. The cabinet is delivered complete with cylinder lock and removable shelves. The tin cabinets have a maximum load per shelf: 100 kg.
The workshop cabinet contains the following:
4 removable shelves
2 removable drawers
1 wide tool board for the back of the cabinet
2 tool boards for the cabinet doors
1 hook set with 56 hooks
5 storage boxes 2013
10 storage boxes 2011
Boltless Universal shelf Starter section, with shelf height 2500 mm.
The universal shelf has 4 shelves in height, with a total capacity of 1600 kg.
The universal shelves help you make maximum use of the space and the shelves are adjustable and fit in stores, regardless of size.
Boltless Universal shelf Starter section, with shelf height 2000 mm, beam width 1500 mm and shelf depth 400 mm.
The universal shelf has 3 shelves in height, with a total capacity of 1200 kg.
The universal shelves help you make maximum use of the space and the shelves are adjustable and fit in stores, regardless of size.
Complete Starter section of Boltless storage shelf with 5 shelves in height, the shelves are placed on two longitudinal shelf beams (L-beam), end walls fitted with reinforcing beams, height 2000 mm.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. These storage shelves have many smart details.
The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg. Increase capacity per shelf further by supplementing with reinforcement beams. Here you can choose from a large selection of starter sections and add-on sections.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross. An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
Boltless storage racks are supplied in different heights, depths and capacities.
Complete electric ESD work table ErgoMulti with 24 mm table top in gray ESD laminate or ESD mat.
The tabletop has a solid wooden edging and grounding terminal on the underside. The table is supplied with a grounding terminal with push buttons intended for ESD wristbands, a grounding contact with ring cable shoe and a terminal block.
The laminate surface gives a table top high scratch resistance and is at the same time resistant to liquids and chemicals.
The table’s maximum load applies with a spread load and lifting speed applies when the table is unloaded. The stroke length of 450 mm provides an optimal working height.
The undercarriage is delivered complete with combined cable protection / extension frame adapted to our wide range of accessories.
Complete electric work table ErgoMulti, including 24mm gray tabletop in high-pressure laminate.
The laminate surface provides a tabletop with high scratch resistance and which is resistant to liquids and chemicals.
The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded. The stroke length of 450 mm provides an optimal working height.
The undercarriage is delivered complete with combined cable protection / extension frame adapted to our wide range of accessories.
Floor stand Comb. 3 consists of 1 double rack base section, 1 double rack extension section, 4 intermediate braces, 3 tool boards, 1 whiteboard, 3 suspension strips, 1 shelf and 22 red trays (8 pcs 3067, 6 pcs 3074 and 8 pcs 3075)
Workshop cabinet Package 2 is a stable fully welded tool cabinet. The cabinet is delivered complete with cylinder lock and removable shelves. The tin cabinets have a maximum load per shelf: 100 kg. The cabinet contains the following: 4 removable shelves 1 removable drawers 1 wide tool board for the back of the cabinet 2 tool boards for the cabinet doors 1 hook set with 56 hooks 4 blue storage trays 2068 4 red storage trays 2068
Complete Starter section of Boltless storage shelf with 5 shelves in height, the shelves are placed on two longitudinal shelf beams (L-beam), end walls fitted with reinforcing beams, height 2000 mm.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. These storage shelves have many smart details.
The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg. Increase capacity per shelf further by supplementing with reinforcement beams.
Here you can choose from a large selection of starter sections and add-on sections. A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross. Boltless storage racks are supplied in different heights, depths and capacities.
ErgoNomi is a table that can be raised and lowered. The stand has intermediate braces for increased stability. The table height is easily adjusted with the crank.
The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded. The stroke length of 450 mm provides an optimal working height.
ESD work table ErgoNomi including extension frame and 24 mm gray ESD laminate table top or ESD mat. The tabletop has a solid wooden edging and grounding terminal on the underside.
The table is supplied with a grounding terminal with push buttons intended for ESD wristbands, a grounding contact with ring cable shoe and a terminal block.
ErgoNomi is a table that can be raised and lowered. The stand has intermediate braces for increased stability.
The table height is easily adjusted with the crank.
Including 24 mm gray table top in high-pressure laminate.
The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded. The stroke length of 450 mm provides an optimal working height.
Floor stand Comb. 4 consists of 1 double rack base section, 1 double rack extension section, 4 intermediate braces, 1 tool board, 1 tool cabinet, 4 suspension strips and 22 red backs (8 pcs 3067, 6 pcs 3074 and 8 pcs 3075)
Workshop cabinet Package 3 is a stable fully welded tool cabinet. The cabinet is delivered complete with cylinder lock and removable shelves. The tin cabinets have a maximum load per shelf: 100 kg. The cabinet contains the following: 4 removable shelves 1 removable drawers 1 wide tool board for the back of the cabinet 2 tool boards for the cabinet doors 1 hook set with 56 hooks
ESD-adapted work and assembly table, with 5 ESD wheels, of which 2 are lockable. Easy regulation with gas cartridge for stepless height adjustment between 620 – 875 mm. Tiltable table top 0-40 degrees. Table top 500×350 mm with razor edge. Powder coated: RAL3000.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
Floor stand Comb. 5 consists of 1 pc double rack base section, 2 pcs additional section, 6 intermediate braces, 3 tool board, 1 tool cabinet, 2 hanging strips and 16 transparent gray storage boxes 96x105x45
Complete manual adjustable work table Light H with 24 mm table top with gray high pressure laminate top. The load capacity applies with a spread load. With the accessory wheel set, the height increases by 135 mm.
Workshop cabinet Package 4 is a stable fully welded tool cabinet. The cabinet is delivered complete with cylinder lock and removable shelves. The tin cabinets have a maximum load per shelf: 100 kg. The cabinet contains the following: 5 movable shelves 1 wide tool board for the back of the cabinet 2 tool boards for the cabinet doors 1 hook set with 56 hooks 8 blue storage trays 3068 8 red storage trays 3068
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
24 mm thick table tops for use in ESD environments.
The top of the tabletop is gray linoleum (U12188MP), the underside has a barrier layer and the top is edged with beech edging. Under the table top there is an ESD ground terminal, GBP ground connection on the right front of the table top.
The linoleum surface gives a table top with a slightly softer expression and has high impact resistance. This table top fits all of our workshop table stands, with the exception of the heavy leg brackets.
Work bench with adjustable leg brackets, 40 mm laminate table top. The capacity is 750 kg distributed load and the working height is 740 – 1010 mm. This is a very stable work table that you can manually adjust in height for the best ergonomics. The table is available in several designs, sizes and with various different add-on details and accessories to meet your specific needs
Workshop cabinet Package 5 is a stable fully welded tool cabinet. The cabinet is delivered complete with cylinder lock and removable shelves. The tin cabinets have a maximum load per shelf: 100 kg.
The cabinet contains the following:
6 movable shelves
8 blue storage trays 3068
8 red storage trays 3068
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
24 mm thick table tops for use in ESD environments.
The top of the table top is high-pressure laminate (HPL), the underside has a barrier layer and the top is edged with beech edging.
Under the table top there is an ESD ground terminal, GBP ground connection on the right front of the table top.
Complete packing table with Bord 400 and high-pressure laminate top in light gray with dark gray edging.
Bord 400 is very flexible and can be easily adapted to specific needs and tasks.
The work table is continuously adjustable with an electric motor. The packing table can handle regular use incl. load up to 400 kg spread load. The table is equipped with a stable intermediate brace.
The combination contains:
1 table top
Superstructure frame
2 perforated pillars incl. assembly kit
6 shelf dividers
2 shelves.
Fully welded stable workshop cabinets that cover your needs for storage in the workshop, warehouse or production. Load per shelf is 100 kg.
Boltless Corner shelf. Capacity is 150 kg/shelf and 1100 kg total capacity for the entire corner shelf.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws.
These storage shelves have many smart details. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams. Here you can choose from a large selection of starter sections and add-on sections.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross. An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
24 mm thick table tops for use in ESD environments.
The top of the tabletop is gray linoleum (U12188MP), the underside has a barrier layer and the top is edged with beech edging.
Under the table top there is an ESD ground terminal, GBP ground connection on the right front of the table top.
Complete packing table with Bord 400 and high-pressure laminate top in grey. Bord 400 is very flexible and can be easily adapted to specific needs and tasks.
The work table is continuously adjustable with an electric motor. It can handle regular use incl. load up to 400 kg spread load. The table is equipped with a stable intermediate brace.
The packing table combination consists of:
Driving and assembly chair, the seat is made of padded conductive ESD artificial leather in black. With steel foot cross, tool shelf and easy-rolling ESD wheels, of which 2 are lockable.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
Robust construction with 3-point locking to withstand heavy loads. The cabinet is equipped with perforated rails for mounting various accessories. The cabinet has a cylinder lock. The workshop cabinet is also available in a variant with an entire perforated panel in each door, see item no. 35-652-2160.
Delivered without accessories. Complete the cabinet with fixed shelves, pull-out shelves, drawers, collection troughs and lighting. Complete with undercarriage for workshop cabinets (truck base), item no. 41-004-7001. The base simplifies the work when moving the cabinet.
The cabinet can be equipped with Flexlock visible for easy keyless use.
Maximum load distributed weight/shelf: 50 kg.
Maximum load distributed weight/cabinet 500 kg.
All-round vinyl table top for work tables with gray vinyl surface edged with dark gray ABS edging.
The set is used for mounting perforated columns on a superstructure frame.
The mounting kit consists of two spring-loaded 4-point nuts, two screws and two washers.
One set is needed per pillar.
Keep the workplace organized with GBP’s practical Assembly Trolley Combination 1. Complete the tool board with GBP’s wide range of accessories. The trolley has a handle and four castor wheels Ø125 mm, of which two wheels with brakes, to be easily moved.
Assembly trolley Comb. 1 consists of:
1 assembly trolley
1 pc Tool board
8 pcs Storage box
1 pc Suspension strip for plastic trays
1 shelf
4 storage boxes
Solo 3660 ESD. A chair with rocking function that offers very good comfort with many variation options. The chair is equipped with a “backrest” that can be rotated 360 degrees around the seat. The “back rest” functions both as a back support, side support and forearm support. The chair is covered with Global antistatic fabric in gray. Footstool in aluminum with antistatic wheels. Seat height 620-802 mm.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
Complete packing table with Bord 400 and high-pressure laminate top in grey. Bord 400 is very flexible and can be easily adapted to specific needs and tasks.
The work table is infinitely adjustable incl. electric motor, they can handle regular use incl. load up to 400 kg spread load. The table is equipped with a stable intermediate brace.
The packing table consists of:
Complete packing table with Bord 400 and high-pressure laminate top in grey. Bord 400 is very flexible and can be easily adapted to specific needs and tasks.
The work tables are infinitely adjustable incl. electric motor, they can handle regular use incl. load up to 400 kg spread load. The table is equipped with a stable intermediate brace.
The combination consists of:
Trolley with 4 ball-bearing wheels and carabiner hook, for use in c-profile rail together with Balance block for mobile suspension of tools or other assembly equipment. If you wish to limit the movement of the running cart, you order end stops in addition.
Tall tool cabinet with plexiglass doors and L-handle. WxDxH 1020x540x2000 mm.
Robust construction with 3-point locking. Equipped with perforated rails for mounting various accessories such as tool panels, fixed and extendable shelves, drawers and drawer compartments.
The cabinet is delivered with 2 plexiglass doors HxW 795x 307 mm. Dimensions of the plexiglass: 770×282 mm. Frame RAL 7004, doors 5002.
Maximum load distributed weight/shelf: 50 kg.
Maximum load distributed weight/cabinet: 500 kg.
Accessories and shelves are purchased separately.
Balance block for tools and assembly equipment. The balance blocks have an easy adjustment for different loads, the durable polyamide line has a working range of 2.0 m and elastic line stop.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
ErgoMini is an electrically adjustable work table that consists of two table legs with integrated motors in each leg.
The stand has intermediate braces for increased stability. The table height is easily regulated with a table control, which is mounted under the top in the table frame.
Including 24 mm table top gray high pressure laminate. The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded.
Packing table Ergomini combination 9 consists of:
Double workshop cabinet with two lockable doors. The cabinet has shelf ladders for mounting shelves.
The top of the cabinet has three resting edges, which can be used as an extra work surface.
The double tool cabinet comes with two pull-out drawers and a shelf.
A workshop cabinet with lockable door and shelf ladders for mounting shelves. The top of the cabinet has three resting edges, which can be used as an extra work surface.
Excl. wheel base.
The workshop cabinet is supplied with a pull-out drawer and a shelf.
Maximum load distributed weight/shelf: 25 kg.
Maximum load distributed weight/box: 20 kg.
Maximum load distributed weight/cabinet: 150 kg.
In our range you will find fully welded tool cabinets with robust construction with 3-point locking to withstand heavy loads. Our lockable tool cabinets are available in single or double versions in various sizes.
Adapt the cabinet to your wishes and furnish them according to your needs, we have many accessories to choose from.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg. Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
Mounting bracket for mounting c-profile rail in fixed arms. 1 mounting bracket is included for each fixed arm, but these can be additionally ordered if you want several c-profile rails mounted – or if there is other equipment to be mounted in the work table’s superstructure. The mounting bracket is adjustable to a certain extent and is basically designed for use with profiles that are 30 x 32 mm.
ErgoMini is an electrically adjustable work table that consists of two table legs with integrated motors in each leg.
The stand has intermediate braces for increased stability. The table height is easily regulated with a table control, which is mounted under the top in the table frame.
Including 24 mm table top gray high pressure laminate. The table’s maximum load applies with a spread load, lifting speed applies when the table is unloaded.
Packing table Ergomini combination 10 consists of:
Verkstadsskåp för väggmontering inkl. fem hyllor.
Skåpet är anpassat för 12/20 st lagerback.
Maxbelastning fördelad vikt/hylla: 15 kg.
Maxbelastning fördelad vikt/skåp: 75 kg.
Solid 600 mm LED work lighting with dimmer for optimal work lighting. The lamps are produced in aluminum and can be angled.
Supplied complete with mounting hardware and 3 m cable and for mounting in a fixed arm for side mounting on the right of the work table.
LED lighting, 19 w with dimming via spring-loaded push button with memory suitable for workplaces that require a high light flux. Angled for the desired direction of light. Fits most workplaces from heavy industry such as lab environments or why not on a packing table.
Boltless shelf systems are stable, galvanized storage shelves that are very easy to assemble without screws. The storage shelves are delivered in four different depths and two widths and with a capacity of 150 kg or 250 kg.
Increase capacity per shelf further by supplementing with reinforcement beams.
A starter section is complete (can stand separately) and consists of 2 end panels, 5, 6, or 7 shelves and back cross.
An add-on section is connected to a starter section or other add-on sections and consists of 1 end, 5, 6 or 7 shelves and back cross.
ESD office chair/industrial chair Active if you have to sit for a long time. Leading chair where the seat and back are covered with a special fabric, where metal wires are woven into the fabric, resistance to earth = 10 ohms. The chair has simple stepless adjustment of both seat and backrest angle using the globally designed seat mechanism and with easy-rolling ESD wheels. Backrest: 16° forward and 6° backward, seat: 12° forward and 3° backward.
Available as a low or high model.
Workshop cabinet for wall mounting.
The cabinet is made of perforated sheet metal for hanging tools. Complete with GBP’s wide range of hooks, which consists of around 50 hooks for different purposes.
The workshop cabinet is prepared for a padlock.
Measure:
Lockable tool cabinet for mounting directly on the wall, alternatively mounted with perforated columns on work tables or assembly trolleys. The cabinet is perforated with 9 mm square holes with cc dimensions 38 mm, mounting hardware included. Measure: Width 870 mm Depth 250 mm Height 715 mm
Complete LED work lighting for installation in our vertical perforated columns. The depth of the fixture is 640 mm from the perforated column. The workplace lighting has integrated LED lights that provide a combination of side and longitudinal light. Supplied complete with arm and bracket and cable with plug. Connects to 230 V – 50Hz. RAL 9006.
A complete longitudinal LED lighting with lighting ramp at the front, integrated LED lights that are adjusted laterally using the magnetic strip. Fits all our tables with extensions, delivered complete.
Complete packing table lightweight H-stand 1500 x 800 mm and 24 mm table top gray high pressure laminate on steel tube base.
The packing table is delivered as pictured and includes:
1 cutting unit with cutting width 1000 mm
1 shelf with width 1340 mm
6 shelf dividers with a height of 200mm
1 axle under the table, mounted on the table base
1 shoulder over the table, mounted between the pillars.
Complete packing table Lightweight H with 24 mm gray high-pressure laminate table top on H-stand base.
The packing table is delivered as in the picture and includes:
1 cutting unit with cutting width 1000 mm
2 shelves with a width of 1340 mm
6 shelf dividers with a height of 200 mm
1 axle under the table, mounted on the table base
1 shoulder over the table, mounted between the pillars.
Complete packing table Light H 1500 x 800 mm and 24 mm gray high-pressure laminate table top on H-stand base.
The packing table is delivered as in the picture and includes:
2 shelves with a width of 1340 mm
6 shelf dividers with a height of 200 mm.
2 perforated pillars
The 7010 ESD saddle chair is an excellent addition to your standing workplace. The shape of the narrow seat is adapted for high working heights. The 7010 ESD is equipped with a backrest. The chair is covered with Global antistatic fabric in gray. Footstool in aluminum with antistatic wheels. Seat height 537-735 mm
Cabinet with perforated sheet metal in the back and on the inside of the door for hanging tools and accessories.
Two fixed shelves are included.
Maximum load distributed weight/shelf: 15 kg.
Maximum load distributed weight/cabinet: 75 kg.
Complete with plastic jaws and hooks from GBP’s wide range of hooks, which consists of around 50 variants for different purposes.
Unique and movable standing support chair that can be used in environments where there are requirements for ESD. The chair is delivered in black underframe and black PU seat. The product has an integrated handle at the back of the seat that makes it easy to move. The seat height can be adjusted from 510-840mm, which means that it is suitable for most individuals.
Muvman for better back health. Muvman senses how your center of gravity changes and follows your movements forward, backward and sideways. This means several important advantages. It makes it almost impossible to sit with a crooked back and it automatically strengthens the important stabilizing muscles.Muvman is the perfect seating solution for active people who alternately want to sit while maintaining good posture both in a lower sitting position and right up to standing height as a standing support. With its unique stroke length, Muvman provides both active sitting and active standing support. The patented active suspension in the liftomat regulates the inclination of the chair so that you always sit straight in the back while maintaining good posture.
Complete busbar for horizontal placement in our perforated columns, C7C 670/900/1340/1800 mm.
The power rail is delivered with 6 grounded contacts, illuminated switch and 3 m cable with grounded plug.
Connects to 230 V – 50 Hz. Designed for use in Norway, Sweden, Denmark and Finland.
Complete power rail, suitable for all tables with extensions, available in all our standard dimensions. A stylish and safe power source as well as keeping the cords you use for your table in order.
The computer cabinet is specially designed to protect computers in a production environment against dirt and shocks.
The PC cabinet (with opening dimensions WxH 590 x 650 mm) has a lockable door with recessed plexiglass and a removable shelf. Separate, lockable and extendable keyboard shelf with mouse holder.
The lower part of the cabinet has a lockable door (opening dimensions WxH 590×855 mm) and is equipped with a removable shelf and ventilation fan with filter.
The computer cabinet is mounted with adjustable feet. Energy panel included with the cabinet.
Complete packing table on heavy leg frames with 40mm light gray tabletop in high-pressure laminate. The edging is dark grey.
Packing table consisting of heavy leg trestle is a stable packing table with manual height adjustment.
The packing table includes:
The packing table is available in various designs and with various attachment details. Welcome to get in touch.
7110L support chair is perfectly suited to medium working heights. The chair has a unique seat that offers good support and relief. The seat has edging at the front to withstand hard wear. The 7110L is equipped with a backrest and an extra deep seat. The chair is covered with Global antistatic fabric in gray. Footstool in aluminum with antistatic wheels. Seat height 430-568 mm
Energy panel that is mounted vertically in one of our pillars. The panel has 4 sockets with switches that light up when the power is on. 3 m cable included.
Energy panel that fits all our tables that have a perforated column. Simple assembly and you have control over the cords you use for your table.
Computer cabinets for industrial use. The cabinet is specially designed to protect computers in a production environment against dirt and shocks. The PC cabinet (with opening dimensions WxH 590 x 590 mm) has a lockable door with recessed plexiglass. The cabinet has a pull-out keyboard shelf with mouse holder. The lower part of the cabinet has a lockable door (opening dimensions WxH 590 x 500 mm).
Complete packing table on heavy leg frames with 40 mm light gray table top in high-pressure laminate. The edging is dark grey.
The packing table is delivered according to text and includes:
Practical perm holder with space for 2 A4 perms, for external mounting on pillars.
The 5004 work chair can be raised and lowered, has an adjustable backrest that can also be adjusted in depth and an angle-adjustable seat. The 5000 series is popular both in lab and industrial environments. 5004 is equipped with a pear-shaped backrest. The chair is covered with Gaja antistatic fabric in gray. Footstool in aluminum with antistatic wheels. Seat height 448-586 mm.
Fully welded chemical cabinet for industry, schools and public administration. Hinged doors with cylinder lock. The cabinet is delivered complete with removable galvanized shelves that have edges for collecting any chemical spills. The cabinet has ventilation valves and a 100 mm ventilation nozzle at the top for connection to external ventilation.
Combined flat screen and keyboard holder, where the fully adjustable screen holder is adapted for screens with VESA 75/100 and the keyboard holder includes a pull-out mouse table. The capacity is 15 kg distributed load.
The screen and keyboard holder is mounted on the included articulated arm, which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Complete packing table on heavy leg frames with 40 mm gray table top in high-pressure laminate. The edging is dark grey.
The combination consists of:
The packing table can be supplemented with other accessories.
Lådfack med 2 x 3 lådor, 450 x 445 x 100 mm.
Lådfacket passar i GBPs verktygsskåp och placeras på Fast hyllplan.
Workplace mat in ESD design. Made of foamed polyurethane (PU). The carpet has chamfered edges. The mat is intended for use in ESD environments with conductive floors. Thickness 11 mm. Color: Black
Shelf with dimensions h x w x d = 120 x 545 x 170 mm for placing picking boxes, designed for optimal placement of 5 of our 2075 boxes.
The pull-out box shelf is mounted on the included articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Articulated shelf on arm for placing picking boxes, provides a better, ergonomic and more efficient workplace.
Tool and small parts washing Maxiclean has two washing systems, which can be used simultaneously or separately. The laundry can either be placed in the closed space and washed automatically by three washing nozzles or washed manually with a washing brush. Maxiclean is intended for aroma-free, low-fat degreasing with a flash point above 70° C. The washing machine is equipped with adjustable feet as standard. Volume of washing liquid: 30 litres. Ventilation connection: Ø 123 mm. Complete with Aroma-free cal Low-fatting agent.
Assembly trolley Comb. 2 has several practical shelves and a tool board. The trolley has a handle and four castor wheels Ø125 mm, of which two wheels with brakes, to be easily moved.
Assembly trolley Comb. 2 consists of:
1 assembly trolley Base
1 pc Tool board
1 pc Backlist plastic trays
1 shelf depth 210 mm
1 shelf depth 300 mm
1 shelf depth 613 mm.
Workplace mat in ESD design with or without push buttons. The mat consists of two layers where the top layer is made of nitrile rubber and a foam-based bottom layer of EPDM. The carpet has chamfered edges. The mat is intended for use in ESD environments. Push button for easy connection to earth. Thickness 12 mm. Color: Black.
This arm has 3 joints, which makes it very flexible. The length of the arm is 570 mm including column attachment, and can be used as a starting point for attaching shelves, tool holders, boards or the like. At the end of the arm there is a through hole for an M8 screw, the height of the attachment is 99 mm and the distance from the center to the outside is 15 mm (excl. end plug).
Double suspension strip for pick and store boxes, optimal for use with our 2075 boxes. This double slat for pick boxes is mounted on the supplied articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace. Maximum load distributed weight 15 kg.
Workplace mat in ESD design. Made of foamed polyurethane (PU). The carpet has chamfered edges. The mat is intended for use in ESD environments with conductive floors. Thickness 15 mm.
Adjustable document holder with h x w = 330 x 290 mm, for the use of upright A4 sheets and documents and with a capacity of 15 kg distributed load.
The document holder is mounted on the accompanying articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Sticky mat that catches dirt and dust from shoes, wheels etc. Placed, for example, at the entrance to clean rooms, ESD rooms or other controlled environments. The mats are easily attached to the floor or to a frame with double-sided tape. A transparent protective layer protects the top part of the adhesive mat until it is ready for use. The corner tabs are sequentially numbered to show the number of sheets remaining and help prevent multiple sheets from being removed at once.
Articulating arm with fully rotatable keyboard holder and mouse pad. The articulated flatscreen holder is mounted on perforated pillars. The mouse pad can be mounted on the left or right side. The plate for the mouse pad is white.
ESD Shelf trolley S100, with 2 shelves. Four swivel wheels 125×32 mm, ball bearing hub and wire protection in ESD design. Especially ESD-protected carts for EPA environments EPA – ESD-Protected-Area). The trolleys are designed for safe dissipation of static electricity. They are approved by RISE Research Institutes of Sweden with SP method 2472 and meet the requirements according to IEC 61340-5-1 and N 100015-1. Shelves in 19 mm conductive board with melamine on both sides. Black ABS edging on all four sides. Shelves and running handles infinitely adjustable to be easily adapted as needed.
Screen holder with fully rotatable universal mount for screens with VESA 75/100 mounting. The capacity is 15 kg distributed load. The screen holder is mounted on the accompanying articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
Adjustable shelf with w x d = 405 x 305 mm, winding edge around the entire shelf and capacity 15 kg distributed load. The tiltable shelf is mounted on the accompanying articulated arm (included), which provides a very flexible, ergonomic and efficient workplace. In the extended position, the arm itself is 570 mm including the column mount, so that necessary equipment will be available in the immediate vicinity of the workplace.
ESD Shelf trolley S100, with 3 shelves. Four swivel wheels 125×32 mm, ball bearing hub and wire protection in ESD design. Especially ESD-protected carts for EPA environments EPA – ESD-Protected-Area). The trolleys are designed for safe dissipation of static electricity. They are approved by RISE Research Institutes of Sweden with SP method 2472 and meet the requirements according to IEC 61340-5-1 and N 100015-1. Shelves in 19 mm conductive board with melamine on both sides. Black ABS edging on all four sides. Shelves and running handles infinitely adjustable to be easily adapted as needed.
ESD Shelf trolley S100, with 2 shelves. Four swivel wheels 125×32 mm, ball bearing hub and wire protection in ESD design. Especially ESD-protected carts for EPA environments EPA – ESD-Protected-Area). The trolleys are designed for safe dissipation of static electricity. They are approved by RISE Research Institutes of Sweden with SP method 2472 and meet the requirements according to IEC 61340-5-1 and N 100015-1. Shelves in 19 mm conductive board with melamine on both sides. Black ABS edging on all four sides. Shelves and running handles infinitely adjustable to be easily adapted as needed.
ESD Shelf trolley S100, with 3 shelves. Four swivel wheels 125×32 mm, ball bearing hub and wire protection in ESD design. Especially ESD-protected carts for EPA environments EPA – ESD-Protected-Area). The trolleys are designed for safe dissipation of static electricity. They are approved by RISE Research Institutes of Sweden with SP method 2472 and meet the requirements according to IEC 61340-5-1 and N 100015-1. Shelves in 19 mm conductive board with melamine on both sides. Black ABS edging on all four sides. Shelves and running handles infinitely adjustable to be easily adapted as needed.
ESD Shelf trolley with 2 shelves in simple design for production and workshop. No gable grates make it easy to handle goods. Especially ESD-protected carts for EPA environments EPA – ESD-Protected-Area). The trolleys are designed for safe dissipation of static electricity. They are approved by RISE Research Institutes of Sweden with SP method 2472 and meet the requirements according to IEC 61340-5-1 and N 100015-1. Shelves in 19 mm conductive board with melamine on both sides. Black ABS edging on all four sides. Shelves and running handles infinitely adjustable to be easily adapted as needed.
Shelf complete with mouse holder, brackets and fasteners. The shelf has expansions, which provide 100% extendability. Mouse pad made of plywood is primed with clear lacquer. The mouse pad, which is white, can be pulled out on the right or left side. The pull-out keyboard shelf can be used on all work tables in our range.
Dimensions: Shelf, 565 x 470 x 95 mm.
Dimensions: Mouse pad, 565 x 210 x 9 mm.
ESD Rolling table with 2 shelves, chassis in bright galvanized 22 mm tubes. Four swivel wheels 125×32 mm, ball bearing hub and wire protection in ESD design. Especially ESD-protected carts for EPA environments EPA – ESD-Protected-Area). The trolleys are designed for safe dissipation of static electricity. They are approved by RISE Research Institutes of Sweden with SP method 2472 and meet the requirements according to IEC 61340-5-1 and N 100015-1. Shelves in 19 mm conductive board with melamine on both sides. Black ABS edging on all four sides. Shelves and running handles infinitely adjustable to be easily adapted as needed.
ESD Rolling table with 2 shelves, chassis in bright galvanized 22 mm tubes. Four swivel wheels 125×32 mm, ball bearing hub and wire protection in ESD design. Especially ESD-protected carts for EPA environments EPA – ESD-Protected-Area). The trolleys are designed for safe dissipation of static electricity. They are approved by RISE Research Institutes of Sweden with SP method 2472 and meet the requirements according to IEC 61340-5-1 and N 100015-1. Shelves in 19 mm conductive board with melamine on both sides. Black ABS edging on all four sides. Shelves and running handles infinitely adjustable to be easily adapted as needed.
Tool panel perforated with 9 mm square hole with CC 38 mm and articulated arm.
Used together with tool hooks for hanging smaller hand tools. The capacity is 15 kg distributed load.
ESD Rolling table with 2 shelves, chassis in bright galvanized 22 mm tubes. Four swivel wheels 125×32 mm, ball bearing hub and wire protection in ESD design. Especially ESD-protected carts for EPA environments EPA – ESD-Protected-Area). The trolleys are designed for safe dissipation of static electricity. They are approved by RISE Research Institutes of Sweden with SP method 2472 and meet the requirements according to IEC 61340-5-1 and N 100015-1. Shelves in 19 mm conductive board with melamine on both sides. Black ABS edging on all four sides. Shelves and running handles infinitely adjustable to be easily adapted as needed.
Cable channel placed on the side of perforated columns, fixed with column end plugs. Cables are pulled in a U-profile 30 x 30 mm, the cable channel has 9 penetration openings evenly distributed over the total length of 1926 mm.
Tool and small parts washing Masterclean has two washing systems, which can be used together or separately.
The laundry can be cleaned in the enclosed space, where it is automatically flushed by six nozzles (of which three are movable from both the bottom and the top) or washed manually with a brush.
Masterclean is intended for aroma-free low-fat degreasing with a flash point above 70° C.
Internal washing space: 850 x 460 x 370 mm.
Volume of washing liquid: 50 litres.
Ventilation connection: Ø 123 mm.
Complete with Aroma-free degreaser.
24 mm thick table tops for use in ESD environments.
The top of the tabletop is gray linoleum (U12188MP), the underside has a barrier layer and the top is edged with beech edging.
Under the table top there is an ESD ground terminal, GBP ground connection on the right front of the table top.
The linoleum surface gives a table top with a slightly softer expression and has high impact resistance. This tabletop fits all of our workshop table stands, with the exception of the heavy leg brackets.
Assembly trolley Komb.3 has three practical tool boards. The trolley has a handle and four castor wheels Ø125 mm, of which two wheels with brakes, to be easily moved.
Assembly trolley Comb. 3 consists of:
1 assembly trolley 3
Tool boards
Perforated tool panel with 9mm square hole with cc measure 38mm.
With the included mounting kit, the board is easily mounted on columns on work tables, on wall rails or on mounting trolleys.
The panel can also be mounted right on the wall.
Tool and small parts wash Microclean is our smallest workshop wash. It is suitable for service, repair and car workshops. Microclean can be placed directly on a workbench or hung at a suitable height on a wall.
The laundry is washed manually using a shower brush. Microclean is the ideal solution for washing small machine and engine parts. The wash is intended for aromatic-free, low-fat degreasing with a flash point above 70° C.
Washing bench dimensions: 510 x 340 mm.
Volume of washing liquid: 8 litres.
Complete with Aroma-free degreaser.
40 mm thick tabletop that has a light gray high pressure laminate (HPL) top edged with a dark gray ABS edging. The HPL surface provides a table top with high scratch resistance and which is resistant to liquids and chemicals. The table tops are pre-drilled with screw inserts for our heavy leg brackets and hurts and consist of a solid wood core and glued fiberboard.
Hook set tool hooks mixed 24-pack.
Hook set 24-pack contains:
Suspension hook 35-711- 5 pcs
Suspension hook 35-715- 2 pcs
Double hook 35-721- 6 pcs
Double hook 35-724- 2 pcs
Bar hook 35-755- 2 pcs
Angle hook 35-750- 3 pcs
Drawer holder with storage tray 41-803- 1 pc
Pipe holder 42-086- 1 pack (2 pcs. Ø 25-22 mm + 1 pc. Ø 37-34 mm, height 75 mm)
Complete with tool board (not included), which i.a. available for mounting directly on a wall, at a work table, in a cabinet or on trolleys. The hooks are hooked into the perforation of the tool board and locked with a stop screw.
The hooks fit GBP’s tool boards, which have a hole dimension of 9 mm (4-edge hole) and hole spacing of 38 mm.
Ball mat in natural rubber thickness 14 mm and in the color black. A good alternative for good ergonomics when working standing. The mat’s profile and elasticity stimulate blood circulation and prevent cramps, circulation and fatigue problems in the feet, legs and back. Made of natural rubber, something that gives a long life and high tear and wear resistance. The carpet is suitable for use in the workshop and wood industry, at package tables and in reception.
Washing basket with lid for Masterclean and Maxiclean workshop washing machines.
Table top for work table. This is a 40mm thick, popular all-round table top with gray vinyl surface edged with gray ABS edging.
Magnetic whiteboard for placement in perforated columns at the back edge of work and packing tables, on floor-mounted L and T stands, on assembly trolleys or directly on the wall.
Necessary mounting details for mounting on the column are included.
Practical whiteboard, write on it or put magnets on it, the areas of use are many. Available in different CC measurements for our different products.
Basket for Masterclean and Maxiclean workshop washers.
Suspension rail for use with storage boxes or modular boxes.
The rail has integrated brackets for straight or angled mounting on our perforated columns. The capacity is 20 kg distributed load. Plastic boxes are not included and must be ordered separately – See related products for the most common plastic boxes used with the suspension rail.
Flush handle complete with brush and hose for workshop washers Microclean, Masterclean and Maxiclean.
Arm with a length of 700 mm, for mounting in our perforated columns. This fixed arm is used together with one or more c-profile rails, for hanging mobile tool holders, work lighting or other mounting material. 1 bracket for c-profile is included, if you want more c-profiles, you order several brackets, 1 per arm / 2 per c-profile.
Shelf with jump plane capacity 50kg distributed load. The storage shelf is delivered with 2 brackets / brackets and is intended for mounting in our perforated columns, at the back edge of work and packing tables, on floor-mounted L- and T-stands or on our assembly trolleys.
The storage shelf is reversible, has a completely flat side and a side with 4 ridged edges and can be placed horizontally or at an angle.
Brush for workshop washers Microclean, Masterclean and Maxiclean.
C-profile rails for mounting work lighting, mobile tool holders or other mounting equipment. The C-profile rail was attached over the work table in a fixed arm with a length of 700 mm.
End stop, consisting of a square washer (25x30x5 mm) with screw and washer for placement in the suspension C-profile.
The extension can also be supplemented with other shelves. The superstructure consists of: 2 Perforated columns (H=820 mm, with fittings for mounting on the underside of the worktop) 1 Perforated tool panel 1 Backlist for plastic boxes 1 Shelf, 875 x 210 mm.
If you attach the T-profile to the post base in addition to using this anchor bolt, you will have an effective tip protection of your storage shelf.
Complete Workbench Dallas. Manually very stable height adjustable leg stand with wheels for 40 mm table top with depth 800 mm.
The leg stand can be mounted either on the right or left with the wheels facing the center of the table. The wheels are firmly mounted, and by stepping on the stirrup the legs are pushed down, height difference between position on legs and on wheels is 10 mm.
All wheels with brake, Ø 150 mm. Max spread load for the table on legs is 500 kg, and 300 kg if the table is on wheels.
We recommend that the tables be fitted with a frame, and that moving tables on wheels should be done without load. High-pressure laminate on the table top provides high scratch resistance and is resistant to liquids and chemicals.
The table tops are pre-drilled with screw inserts for legs and frames and consist of a solid wood core and glued wood fiberboard.
The maximum capacity refers to an evenly distributed load. Don’t forget to order a superstructure frame and other superstructures.
Lighting set consisting of 1 C-profile L-1490 mm, 2 fixed arms L-700 mm and light fitting LED 38W.
Solid LED work lighting with dimmer for optimal work lighting. The lamps are produced in aluminum and can be angled.
The perfect carpet for a public environment, in offices or at packing stations. Optimal-KOMBI is an ergonomic mat in two layers for dry workplaces. Very high elasticity and load-bearing capacity while being easy to clean. Bevelled edges around the entire carpet as standard. This product is delivered in the color Black (product image shows light grey). The carpet can also be obtained in 15 and 23 mm thickness.
Assist is an ergonomic work chair that stimulates the back and legs, for those who work sitting or standing. The chair has a comfortable PU seat for easy cleaning, as well as stepless adjustment of seat angle and working height. For the highest version of Assist, we recommend the use of sliding feet.
Below you will find additional equipment.
This version of the Assist work chair has the unique V-MATIC seat mechanism, which provides free movement in all directions. ASSIST V-MATIC is thus an ergonomic work chair which, through active sitting, stimulates the back and neck and prevents strain injuries. The chair has a comfortable PU seat for easy cleaning, as well as stepless adjustment of the working height. For the highest version of ASSIST V-MATIC we recommend the use of sliding feet.
Seat height low: 420 – 550 mm
Seat height high: 560 – 820 mm
Below you will find additional equipment.
Set with right and left armrests, including fittings for attachment to the mechanism of our GBP industrial chairs, model Industry, Dynamic and Dynamic Comfort.
Aromatic-free, low-fat degreaser suitable for cleaning steel, iron, stainless steel, aluminium, brass and copper.
Degreasing agent with a weak fragrance is an effective washing liquid for use in the workshop washers Microclean, Masterclean and Maxiclean. The agent removes oil, grease, soot, wax, graphite, tar and asphalt.
Dissolved greasy impurities can be blown away with compressed air or wiped away with a cloth or similar.
Degreaser leaves a rust-protective film and is stored cool and away from sources of ignition.
Divider bracket for sloping shelf 1000 x 500 mm.
Practical Ø36 x 300 mm divider pipe including cargo cover and end plugs, adapted for mounting set for vertical storage. In total there is room for 9 dividers.
Wire basket in galvanized version with height 240mm and mesh width 27mm, adapted for shelves with 1000mm width and 500mm depth. The baskets have a maximum load of 35 kg evenly distributed. For optimal division of the wire basket, order customized dividers. Supplied including shelf hooks.
Practical shelf dividers for placement on Boltless shelves. The divider is delivered in a galvanized version and with mesh width 45 x 50 mm.
Galvanized shaft for mounting between our vertical perforated columns. The packing table shaft is supplied complete with Ø25 mm galvanized pipes and the necessary brackets for attachment to the uprights.
Galvanized shaft on console for front or rear suspended mounting on our vertical perforated columns. The packing table shaft is supplied complete with Ø25 mm galvanized pipes and the necessary brackets for attachment to the columns.
Galvanized shaft for mounting under packing tables with a width of 1500/2000 mm. The packing table shaft is delivered complete with Ø25 mm galvanized pipes and the necessary fasteners for attachment to the table base. Applies to stands Light H and Heavy leg stand.
ASPB model 2 is a complete back cabinet, consisting of the fully welded ASHV steel cabinet with doors in anthracite, blue or light grey and in combination with the necessary number of shelves and 130 storage trays with d x w x h = 400 x 115 x 100 mm.
ASPB model 4 is a complete back cabinet, consisting of the fully welded ASHV steel cabinet with anthracite, blue or light gray doors in combination with the necessary number of shelves, 48 storage shelves with size 400 x 115 x 100 mm and 28 storage shelves with size 400 x 230 x 100 etc.
ASPB model 4 is a complete storage cabinet, consisting of the fully welded steel cabinet ASHV with anthracite, blue or light gray doors in combination with the necessary number of shelves, 60 storage trays with size 400 x 115 x 100 mm and 35 storage trays with size 400 x 230 x 100 etc.
Box rack Simple consisting of L-floor rack with height 1850 mm, necessary suspension rails and the following backs: 12 pcs 9073, dxbxh = 350x206x150 mm / 18 pcs 9074, dxbxh = 250x148x130 mm / 24 pcs 9075, dxbxh = 170x105x75 mm.
Ryggstativ Enkelt bestående av L-golvstativ med höjd 1850 mm, nödvändiga upphängningsskenor och följande ryggar: 54 st 9074, dxbxh = 250x148x130 mm.
Box rack Double consisting of T-floor rack with height 1850 mm, necessary suspension rails and the following backs: 28 pcs blue and 28 pcs red 9073, dxbxh = 350x206x150 mm.
Box rack Double consisting of T-floor rack with height 1850 mm, necessary suspension rails and the following backs: 24 pcs 9073, dxbxh = 350x206x150 mm / 36 pcs 9074, dxbxh = 250x148x130 mm / 48 pcs 9075, dxbxh = 170x105x75 mm.
Box rack double consisting of T-stand for storage, necessary suspension rails and the following trays: 108pcs 9074, dxwxh = 250x148x130 mm.
Box rack Double consisting of T-floor rack with height 1850 mm, necessary suspension rails and the following backs: 24 pcs 9073, dxbxh = 350x206x150 mm / 60 pcs 9074, dxbxh = 250x148x130 mm / 16 pcs 9075, dxbxh = 170x105x75 mm.
Box rack consisting of L-floor rack with height 1850mm, necessary suspension rails and the following backs: 28 pcs 9073, dxbxh = 350x206x150mm.
Practical strips with a height of 55mm for Boltless shelves. The back edge strip works as an edge strip at the back edge of the shelves so that the goods do not fall through. Supplied in galvanized version.
Bench brush ESD 65x370mm
Bench shovel ESD
Basic is a work chair with a polyurethane seat that makes cleaning easier. The low version comes with wheels, while the high version has footrests and sliding feet.
Pack of 5 Ø50 mm load-braking wheels for our industrial chairs. The wheels also fit other chairs with a wheel cross adapted for 11 mm pin for attachment.
The wall bracket secures the stability of your Boltless storage shelves by anchoring the shelf ends to the wall. Calculate 1 fitting per ladder in the storage shelf.
Bracket for lateral mounting in T-profile to attach to wall. The fitting is used as a tipping protection of your storage shelf, where you do not get a tipping protection for top mounting (recommended).
Lockable desk drawer with expansions that provide 100% extendability.
The box is mounted in the table stand using suspension profiles or screwed directly into a heavy (40 mm thick) table top.
Inside box dimensions: W300 x D460 mm.
The suspension profiles are ordered separately. Complete with drawer interior in gray sheet steel or red plastic.
Lockable desk drawer with expansions that provide 100% extendability.
The box is mounted in the Lätt H table stand using suspension profiles or screwed directly into a heavy (40 mm thick) table top.
Inside box dimensions: W450 x D605 mm.
The suspension profiles are ordered separately.
Delivered in a roll measuring 1×10 meters
Table top for work tables with oak parquet surface and front edge in anodised aluminium.
Back edge and sides are in dark gray ABS. The table tops are pre-drilled with screw inserts for our heavy leg brackets and hurts and consist of a solid wood core and glued fiberboard.
Table top for work table, with width 1200 mm and depth 800 mm. This 40mm thick table top has a steel surface, the side edges consist of a blue ABS edging strip.
The steel surface covers the front and back edge of the table top and is also tucked under the front edge for maximum wear resistance. The table surface consists of a 1.5 mm thick, electro-galvanized steel plate, which makes it very well adapted to heavier workshop work.
The table tops are pre-drilled with screw inserts for our heavy leg brackets and hurts and consist of a solid wood core and glued fiberboard.
Drill holder with space for 32 different drills. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Hook Box holder for hanging a plastic box. Available as holder only but also incl. box.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Heavy leg trestle, lifting function wheels D745 mm RAL7004. Manually raise and lower wheels.
Practical Distance bracket when mounting Boltless storage shelves back-to-back. The fitting ensures stable installation with adjustable distance between the shelves. Supplied galvanized and in packs of 1.
Practical distance bracket when attaching Boltless storage shelves to the wall. The fitting ensures stable mounting with an adjustable distance to the wall from 175 mm to 325 mm. Supplied galvanized and in packs of 1.
Document clip 60 mm. Supplied in 1-pack.
Door section Light gray 2100x1000mm, Do you need to lock the shelf. Combined with a tight back and tight or perforated ends, this lockable door set gives you the option to lock all or parts of the shelf! Simple installation in the starter or add-on section. Perfect addition to your storage shelf, storage shelf, shelf.
DYNAMIC COMFORT is an ergonomic quality chair with body-shaped seat and back in PU foam. The asynchronous adjustment mechanism can be easily adjusted while sitting on the chair. Dynamic has stepless adjustment of the seat, back angle and seat height. Supplied with or without armrests. For the highest version of DYNAMIC COMFORT, we recommend the use of sliding feet.
Below you will find additional equipment.
Single column table TL18 800×800 mm (rec. Board size 800×800 mm). The table stand of the single-column table consists of a stable lifting column TL18 made of aluminum with an integrated motor. The table has a capacity of 200 kg distributed load and lifts 22 mm per second without load. The table height is easily regulated with a table control that is mounted under the top in the table frame. The stand is delivered with an extension frame as standard. Table top ordered separately, choose between gray laminate or gray vinyl. Suitable discs can be found below as a related product.
Ergo Classic is a workplace mat made of recyclable vinyl with a thickness of 10 mm. Ergo Classic provides good ergonomics as it contains microcells with millions of air bubbles. The ribbed surface layer provides good friction and good slip protection. The chamfered edges reduce the risk of tripping. The carpet’s soft cushioning properties also contribute to the anti-slip properties. The carpet effectively insulates against cold and vibrations.
The carpet meets the R10 DIN 51130 anti-slip standard. Ergo Classic is best suited in front of workbenches and machines in dry, light work environments such as warehouses, blacksmithing, packing tables and assembly lines. The carpet is ordered in pieces or per meter.
Ergonomic mats for the workplace are very important to relieve the leg and back when working standing. It can also reduce sickness absence and prevent wear and tear injuries.
Workplace mats are intended for standing work on hard floors and provide some sound attenuation and insulate against cold floors, all mats provide a shock-absorbing effect and increased comfort and safety.
Ergo Soft workplace mat is a relief mat. Sturdy and durable surface layer in natural rubber and a soft, resilient underside ensure good traction and best relief. Marbled upper surface makes Ergo Soft easy to keep clean. This means that the workplace mat is perfectly suited to dry industrial environments, at assembly lines, at shop and reception desks and for adjustable tables. Rounded corners and chamfered edges all around, which close tightly to the floor, are standard.
The carpet is PVC-free. Ergo Soft has a 5-year guarantee against wear and tear. Available in black and grey.
Ergonomic mats for the workplace are very important to relieve the leg and back when working standing. It can also reduce sickness absence and prevent wear and tear injuries. Workplace mats are intended for standing work on hard floors and provide some sound attenuation and insulate against cold floors, all mats provide a shock-absorbing effect and increased comfort and safety.
Durable workplace rug Ergo Stripe with colander-patterned surface layer. Soft and cushioning underside of polyvinyl for good ergonomics and comfort. The chamfered edges reduce the risk of tripping.
12 mm thickness provides good ergonomics and the mat effectively insulates against cold and vibrations. Ergo Stripe is best suited in front of workbenches and machines, in dry, light work environments such as shops, warehouses, blackout, packing tables and assembly lines. The carpet’s soft cushioning properties also contribute to slip protection.
Ergonomic mats for the workplace are very important to relieve the leg and back when working standing. It can also reduce sickness absence and prevent wear and tear injuries.
Workplace mats are intended for standing work on hard floors and provide some sound attenuation and insulate against cold floors, all mats provide a shock-absorbing effect and increased comfort and safety.
Ergo Trax is a hard-wearing workplace mat with a colander-patterned surface layer. Soft and cushioning underside of polyvinyl for good ergonomics and comfort. The chamfered edges reduce the risk of tripping. 13 mm thickness provides good ergonomics and the mat effectively insulates against cold and vibrations.
Ergo Trax is best suited in front of workbenches and machines, in dry light work environments such as shops, warehouses, blackening, packing tables and assembly lines. The carpet’s soft cushioning properties also contribute to the anti-slip properties.
Ergonomic mats for the workplace are very important to relieve the leg and back when working standing. It can also reduce sickness absence and prevent wear and tear injuries.
Workplace mats are intended for standing work on hard floors and provide some sound attenuation and insulate against cold floors, all mats provide a shock-absorbing effect and increased comfort and safety.
Ergo Weld workplace mat is a relief mat specially developed for workplaces where grinding and welding work is carried out. Ergo Weld is fire tested and approved according to class B1. The mat has a surface layer of fire-retardant vinyl and a soft back for good ergonomics.
Areas of use: Heavy industry, workshop floors (oil resistant), grinding and welding workplaces.
Ergonomic mats for the workplace are very important to relieve the leg and back when working standing. It can also reduce sickness absence and prevent wear and tear injuries.
Workplace mats are intended for standing work on hard floors and provide some sound attenuation and insulate against cold floors, all mats provide a shock-absorbing effect and increased comfort and safety.
Light H extraction table is a motor-driven industrial table that can be raised and lowered for work where there is exposure to, for example, sanding dust and smoke. The table has extraction through a grid-equipped worktop. Supplied with table top in perforated sheet metal fitted with a durable rubber mat that protects the surface of your workpieces. Exhaust fan not included. Max load 150 kg, distributed load. Adjustable working height 700 – 950 mm. Extraction connection. dia. 200 mm.
ErgoMini extraction table is a motor-driven industrial table that can be raised and lowered for work where there is exposure to, for example, sanding dust and smoke. The table has extraction through a grid-equipped worktop. Supplied with table top in perforated sheet metal fitted with a durable rubber mat that protects the surface of your workpieces. Exhaust fan not included. Max load 180 kg, distributed load. Adjustable working height 710 – 1160 m. Extraction connection. dia. 200 mm
The ErgoSingel TL18 workstation is a stand that can be raised and lowered. Aluminum column TL18 with cable out in outer profile with strong, galvanized top and floor plate.
Plate dimensions: 495 x 495 x 8 mm. Simple height adjustment with table control between 710 -1210 mm, excluding table top. The pillar station should be bolted to the floor.
It can also be used standing loosely on the floor, if you make sure that there is no tipping risk. Supplied complete with large top and bottom plate, control unit and table control for electrical connection.
The stand is prepared for an extension frame, which is ordered separately. Tabletop and add-on accessories are ordered separately. Width of superstructure, to be used, is 670 mm. The station is adapted for a depth of 600 mm, when a superstructure is used.
ESD table mat for loose placement on table surface. The carpet has st. 3 push-button connections with a diameter of 10 mm for connecting earth.
Available in different sizes and colors, see below.
24mm thick shelf complete with brackets for use in ESD environments.
The top of the table top is high-pressure laminate (HPL), the underside has a barrier layer and the top is edged with beech edging. Under the table top is an ESD earth terminal.
HPL provides a tabletop with strong scratch resistance and great resistance to liquids and chemicals.
Conductive Europaback ESD which is ideal for transporting and storing ESD sensitive parts.
Designed to fit pallets with standard dimensions 1200×800 mm and 1200×1000 mm. Stackable. Max load 500 kg.
Fixed panel for tool trolley SMV.
Consisting of 1 x perforated tool board height 640 width 718 mm and 2 x perforated pillars and fittings.
For the lifting columns TL3 and TL 18, the desired hand control must be selected. We also recommend ordering fittings for attaching the control box (2 pcs for 4-parallel columns).
We also recommend ordering fittings for attaching the control box (2 pcs for 4-parallel columns). For TL3, a top and bottom plate must be ordered in addition, 2 per column.
Ring key holder is a vertical ring key holder for eight ring keys. Galvanized. Sell 1 pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Magnifying lamp ESD 5 diopters.
Wave LED in black version with 3.5 diopters, is an ESD-approved magnifying lamp adapted for industrial environments.
This black LED magnifying lamp is approved for use in ESD environments, comes with 2 x 400 lm LED light source and a flexible self-balancing arm. It offers shadow-free magnification with light from both sides.
The storage case is mounted in the table stand using suspension profiles that are ordered separately. Hurtsen can also be screwed directly into a heavy table top (40 mm).
Does not fit when lower shelf is used.
The storage case fits all tables in the wide range. The desk section can be locked with a central lock.
The Hurtsars are equipped with ball-bearing expansions, which provide 100% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order inside the drawers. Drawer division, number x height (mm): 3×100. Maximum load distributed weight: 100 kg.
The storage case is mounted in the table stand using suspension profiles, which are ordered separately.
Drawer division, number x height (mm): 2×100. Maximum load distributed weight for Hurts: 100 kg.
Hurtsen can also be screwed directly into a heavy table top (40 mm). Not suitable when the lower shelf is used.
The storage case fits all work tables and workbenches in the wide range. The Hurtsen can be locked with a central lock. The Hurtsars are equipped with ball-bearing expansions, which provide 100% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order inside the drawers.
The storage basket is used freestanding, with or without a wheel base.
The Hurtsen can be locked with a central lock. Box division, number x height (mm): 1×50 + 3×100 + 1×150.
The Hurtsars are equipped with ball-bearing expansions, which provide 100% extensibility.
Maximum load distributed weight for Hurts: 100 kg.
Complete with interior decoration for the drawers to create order and order inside the drawers.
The wheel base is ordered separately.
Chrome foot ring with size Ø 450mm for use on our industrial chairs. The foot ring is height adjustable and fits on chairs where the cylinder has a maximum diameter of Ø50 mm.
Front edge strip with a height of 90mm, calculated for use with shelves. These are very practical moldings that work as edging. Can be used both at the front and back of the shelves, adapted for use in Boltless shelves. Supplied in galvanized version like other Boltless parts.
Front plinth for the Boltless shelf system, height 90 mm. Galvanized, including two plastic plugs for mounting.
Front bracket for sloping shelf 1000 x 500 mm. The front bracket is attached to the T-profile and covers the entire front of the sloping shelf.
Practical shelf fronts in a galvanized version with a height of 80mm, intended for Boltless shelves.
Complete gable for Boltless shelves
Tight side plate is used as a partition between shelves or as a start and end wall, galvanized steel.
Door set with unique key for each door, for use in Boltless storage rack with width 1000 mm.
End filling in 3 mm galvanized mesh (mesh width is 50 x 50 mm) adapted for our shelves with a height of 2000 mm. Gable filling in net is delivered including fastening hooks.
Package of 5 sliding feet for our GBP industrial chairs and for other chairs with wheel cross adapted for 11 mm pin for attachment. The sliding foot has a diam. Ø35 mm with a bearing surface of Ø50 mm. The height of the sliding foot builds 50 mm.
Floor brush color black.
Floor brush with shovel.
Hand control for TL3 and TL18 including 600mm spiral cable, for flexible use of the work table. Powerful motorized aluminum columns with galvanized floor and top plate. Supplied with control unit and supplemented with optional hand or foot control for height adjustment etc. To be completed with top and bottom plate.
For the lifting columns TL3 and TL 18, the desired hand control must be selected. We also recommend ordering fittings for attaching the control box (2 pcs for 4-parallel columns). For TL3, a top and bottom plate must be ordered in addition, 2 per column.
Wrist strap ESD metal adjustable, to properly secure your ESD workplace, with 10 mm connection point.
Wrist strap ESD red, to properly secure your ESD workplace, with 10 mm connection point.
Wristband ESD metal adjustable, to properly secure your ESD workplace, with 7 mm connection point.
Hanging bracket / Shelf hook for Boltless corner shelf, used when hanging shelves in corner shelves. Calculate 2 hanging brackets per shelf.
Wheel set adapted for use with our lightweight work tables. The set consists of 4 swiveling Ø100 mm rubber wheels, 2 of which are lockable, and with reinforced foot sleeves.
Wheel set adapted for use on our heavy leg stands / industrial tables. The set consists of 4 swiveling Ø125 mm rubber wheels, 2 of which are lockable, as well as reinforced foot sleeves. The capacity is 70 kg / wheel, a total of 280 kg.
Wheel set for work tables ErgoMini 2 and ErgoNomi is complete and consists of 4 double wheels, lockable castors with Ø75mm diam. Height 99 mm, bolt diameter 10 mm.
Wheel set for work table ErgoMulti 2 and Bord 400 is complete and consists of 4 double wheels, lockable castors with Ø75mm diam. Height 99 mm, bolt diameter 10 mm.
Pack of 5 Ø50 mm standard easy-rolling wheels for our GBP industrial chairs. The wheels also fit other chairs with a wheel cross adapted for 11 mm pin for attachment.
.
A complete set of wheels for one or two-post tilting tables ErgoTilt. The set consists of 4 castors with total brake and rubber track, diameter 160 mm. The wheels are mounted on a steel tube adapter. The wheel set raises the tilting table 40 mm.
Pack of 5 Ø50 mm slow-rolling wheels for our GBP industrial chairs. The wheels also fit other chairs with a wheel cross adapted for 11 mm pin for attachment.
The wheel base for the ErgoLite tool cabinet consists of a steel plate with four swiveling wheels Ø75 mm, two of which have brakes. The wheel base increases the total height of the double tool cabinet by 95 mm.
Raised tool panel with lock 960×540 mm for mounting on GBP tool trolley. The frame can be easily retrofitted with 4 screws.
Comes with two powerful gas pistons on each side of the board.
Maximum load on board: 15 kg.
Extra shelf for Boltless corner shelf with capacity 250 kg. The shelf complete with 2 shelf hooks and 2 hanging brackets for attachment to shelf type B in a corner shelf.
Shelf is provided with hooks, which fit the perforation in the panel. Galvanized. 1 pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Extra shelf for Boltless storage shelf with capacity 150 kg. This shelf is delivered in a powder-coated version in light gray RAL7035.
Extra shelf for Boltless storage shelf with capacity 150 kg. This shelf is delivered in galvanized steel.
Extra shelf for Boltless storage shelf with capacity 250 kg. This shelf is delivered in a powder-coated version in light gray RAL 7035.
Extra shelf for Boltless storage shelf with capacity 250 kg. This shelf is delivered in galvanized steel.
Extra shelf for Boltless universal shelf, for shelf with capacity 400kg. The shelf is delivered complete with 2 shelf beams, additional shelves and safety pins.
Shelf for bar code gun/scanner, tape dispenser or as a storage shelf, the shelf intended to hang on a backboard.
Shelf with telescopic rails fits GBP’s workshop cabinet. Fully extendable shelf. The shelf is mounted on telescopic rails.
The shelf can be mounted with a smooth top or with a sharp edge for e.g. furnishings with small details. Complete with GBP’s drawer interior in red plastic, which is available in various designs.
With the workshop cabinet doors opened 90°, the shelf can be pulled out to 110%. The cabinets therefore do not require extra side space, but can be placed close together or in a corner.
Shelf divider for use as a binder support, side support or other type of demarcation.
The compartments are delivered in 2-packs and are adapted for shelves with a depth of 300mm.
Use the divider for e.g. binders, books or as a cardboard support, our dividers can be used for most things, give a structured impression, order and order!
Shelf divider, a practical dividing plate in two height options that is placed in slots of CC 50 mm in the shelves. Fits both in your galvanized or lacquered archive shelf / storage shelf.
Boltless universal shelf shelf beam with capacity 400 kg (in combination with Boltless steel shelves). For beams with a width of 1500 mm, 2 750 mm wide shelves are used in the desired shelf depth. Alternatively, the shelf beam can be used in combination with chipboard, in which case we recommend the use of a minimum of 2 cross beams for the desired shelf depth.
L-shaped shelf beam with width 750, 1300 or 1000 mm and capacity 150, 250 kg in combination with Boltless steel shelves.
Shelf amplifier for Boltless shelf. With this shelf amplifier, you increase the capacity of the shelf by 50 kilos.
With shelf amplifiers, you increase the capacity of your archive shelf / warehouse shelf to 200 kg (widespread load).
Do you want to build it yourself or do you perhaps need extra shelves for the starter and companion sections that are defined as standard? Here you will find the necessary products to adapt your archive shelf or storage shelf to your own needs.
ESD mat for placement on a shelf. The mat has 2 10mm push buttons for necessary connection.
Build and adapt the workplace for safe and effective dissipation of static electricity. Discharges of static electricity ESD (Electro Static Discharge) cause great damage every year in the electronics industry. It is becoming increasingly important to protect sensitive electronics against ESD damage.
Shelf mat ESD with black rubber. Delivered in a roll measuring 0.6×24 meters.
Extra shelf for Boltless FIFO shelf (First In – First Out storage method), The shelf has a 15 mm high front edge that prevents goods from sliding off. The shelf is delivered complete with 2 shelf beams.
Fixed shelf for GBP’s workshop cabinet. The shelf is delivered with four shelf hooks per shelf for mounting in the cabinet’s perforated rails.
Supplied in 2-packs.
Fixed shelf for GBP’s workshop cabinet. The shelf is delivered with four shelf hooks per shelf for mounting in the cabinet’s perforated rails.
Supplied in 2-packs.
Shelf for SMV tool cabinet with width 1000 mm including shelf hooks for the shelf. 80 kg evenly distributed.
Extra shelf for starter or add-on section to shelf system V06.
L-shaped shelf beam with width 750,1000 mm capacity 150,250 kg in light gray version RAL 7035. The shelf beam is used in combination Boltless steel shelves.
Industrial carpet. Made of foamed polyurethane (PU). Dimensions: 0.6×0.9 meters. Thickness 15 mm. Color: Black
The workplace mat Ergo Durk is ESD-approved with the dimensions 1400 x 1000 mm, the work mat is a hard-wearing mat with a two-layer structure, which provides very good comfort. The surface has a modern industrial design that makes it non-slip and meets today’s HSE requirements.
Nitricell’s underside is springy and elastic and relieves feet, legs and back throughout the working day. The floor mat is ESD approved with the possibility of connection to ground.
COMFORT is a draining and oil-resistant mat made of pure nitrile rubber to withstand lying in tough environments. COMFORT is designed to increase comfort for staff while reducing the risk of tripping accidents. COMFORT is treated to become antibacterial and can withstand most chemicals and oils for a long time. As standard, COMFORT is delivered in 3 different sizes.
This cone-shaped, ergonomically constructed profile reduces fatigue by stimulating muscle activity and circulation. The perfect carpet for commercial kitchens, food industry, laboratories and hospital environments. Designed to be easy to clean. Good ergonomics combined with chemical resistance. HYGIEN can be autoclaved (in size 0.60×0.90 m) and has very good antibacterial cleanability. Available in 4 different colors for easy identification and cross contamination control. Meets USDA and CFIA standards/guidelines. Cleanroom ISO class 2 (class 100). As standard, HYGIEN is delivered in 3 different sizes, but it can also be customized completely freely in size.
A very good mat specially developed for light and heavy industrial environments. The mat is resistant to oils, many alkaline liquids and acids as well as hot drill chips up to 600 ºC. NITRO has a unique rounded cone-like design that gives the product very good ergonomics while the slip protection is unique.
Ergonomic mat in two layers for dry workplaces where oil spills may occur. High elasticity and load-bearing capacity. Very durable and non-slip with a pyramidal profile. Chamfered edges around the entire carpet reduce the risk of tripping.
RINGO is a draining and oil-resistant mat made of pure nitrile rubber to withstand lying in environments where oil or chemical spills may occur. RINGO increases comfort for staff while reducing the risk of tripping accidents.
Ergonomic mat in two layers for dry workplaces where oil spills may occur. High elasticity and load-bearing capacity, easy to clean. Chamfered edges around the entire carpet that reduce the risk of tripping. Stated in running meters.
Industrial chair 5002 ESD work chair can be raised and lowered, has an adjustable backrest that can also be adjusted in depth and an angle-adjustable seat. The 5000 series is popular both in lab and industrial environments. 5002 is equipped with a medium height backrest. The chair is covered with Gaja antistatic fabric in gray. Footstool in aluminum with antistatic wheels. Seat height 448-586 mm
8000 ESD work chair has many and unique setting options. The chair can be raised and lowered, has an adjustable backrest that can also be adjusted in depth and an angle-adjustable seat. The chair is equipped with a rocking function, adjustable armrests and a headrest in artificial leather. The chair is covered with Gaja antistatic fabric in gray and has a padded seat for extra durability. Footstool in black aluminum with antistatic wheels. Seat height 449-587 mm. Chair 8000 is our most requested work chair.
Antistatic chair, perfect for anyone who works with sensitive electronics. Seat and backrest in conductive polyurethane and with easy rolling ESD wheels. The chair has simple stepless adjustment of both seat and backrest angle using the globally designed seat mechanism. Backrest: 16° forward and 6° backward, seat: 12° forward and 3° backward. Polyurethane foam provides good seating comfort and is practical and robust – even in the harshest environments. Polyurethane is resistant to many types of liquids and chemicals and is also easy to clean. High model is always on sliding feet and with footrest.
Industrial chair – Industry is part of our large range of GBP quality chairs. Available with cylinder low, medium and high seat height 440 – 580/550-730/630-880 mm. Wheel cross Ø600 mm, wheel type: Ø50 mm, easily rolled. (other wheel types/sliding feet are available as an option). Seat and back with black alto graphite gray textile or black vinyl. Foot ring and armrest are available as options.
Below you will find additional equipment.
Dynamic industrial chair is part of our large range of quality chairs and has a seat/back in PU foam. Available with cylinder low, medium and high seat height 400 – 530/520-700/600-850 mm. Wheel cross Ø600 mm, wheel type: Ø50 mm, easy rolling. (other wheel types/sliding feet are available as an option). Foot ring and armrest are available as options.
Below you will find additional equipment.
This is a practical standing support chair with a seat made of PU foam for good sitting comfort. The seat can be tilted and follows your movements, so you avoid unnecessary wear and tear on your back, hips and legs. The seat height of the chair is adjustable 620 – 850 mm and the seat surface is 320×220 mm. Non-slip floor protection is mounted on the undercarriage.
ESD grounding cable with length 15 cm with a ring cable lug at each end, ø 6mm. Black. Intended for the diversion of two parallel ESD shelves or backlist. Excl. screw.
Grounding cable ESD Rk 0.75mm2 L-15 cm ring shoe/ring shoe
ESD grounding cable with a length of 2 meters with a ring cable lug at each end, ø 6mm. Black. Intended for the diversion of ESD table tops or shelves. Excl. screw.
Grounding cable ESD Rk 0.75mm2, L-2.0m ring shoe/ring shoe.
Ground terminal with dimensions 110x37x16.5 mm adapted to require little space. Can be advantageously mounted under the tabletop on the workstation. Black connection cable, length 3 meters and a ring cable shoe included.
Clothes rail supplied complete with screws and holders for Boltless storage shelves with a depth of 600 mm and a width of 1000 mm. Maximum load is 45kg.
Complete section of Boltless FIFO shelf ( Storage method First In – First Out ) with 8 shelves in height, 7 sloping with 14° inclination and with a 15 mm high front edge, the top shelf is flat, the shelves are hung on shelf holders.
Capacity per shelf is 150 kg, total capacity for a complete section is 1300 kg
Cup for e.g. spray cans and small gadgets. Galvanized. The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw. The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm. The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Hook set tool hooks mixed 20-pack
Hook set 20-pack contains:
Suspension hook 35-713- 4 pcs
Single hook 35-731- 6 pcs
Spring clamp 35-766- 3 pcs
Spring clamp 35-767- 3 pcs
Double hook 35-722- 4 pcs
Hook set tool hooks mixed 56-pack
Hook set 56-pack contains:
Suspension hook 35-711- 20 pcs
Double hook 35-721- 10 pcs
Bar hook 35-755- 5 pcs
Angle hook 35-750- 5 pcs
Ring hook 35-760- 1 pc
Ring hook 35-761- 1 pc
Spring clip 42-464- 10 pcs
Pipe holder 42-086 1 pack
Cup 35-780- 1 pc
Complete with tool board (not included), which i.a. available for mounting directly on a wall, at a work table, in a cabinet or on trolleys. 42-464-0001 replaces part number 41-962-0001.
The hooks are hooked into the perforation of the tool board and locked with a stop screw.
The hooks fit GBP’s tool boards, which have a hole dimension of 9 mm (4-edge hole) and hole spacing of 38 mm.
Complete cross brace for use with Boltless starter and add-on section, for storage shelves with width 750 and 1000 mm.
Drawer with telescopic rails fits GBP’s fully welded workshop cabinets.
Fully extendable drawer, which is mounted on telescopic rails. With the workshop cabinet doors opened 90°, the drawer can be pulled out to 110%. The cabinet therefore does not require any extra side space.
The workshop frame is mounted in the table stand using suspension profiles or screwed directly into a heavy table top (40 mm). Fits Heavy leg stand and Light H stand.
Box division, number x height (mm): 1×50 + 1×150 + 1×200. Maximum load distributed weight for desk drawer section: 175 kg.
Suspension profiles for Light H-stand are ordered separately. Lockable with central lock. Built-in safety, which means that only one drawer can be pulled out at a time. The desk drawer section is equipped with ball-bearing expansions, which provide 110% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order.
The workshop frame is mounted in the table stand using suspension profiles or screwed directly into a heavy table top (40 mm). Fits Heavy leg stand and Light H-stand depth 800 mm.
Drawer division, number x height (mm): 4×100. Maximum load distributed weight for Hurts: 175 kg.
Suspension profiles for Light H-stand are ordered separately. Lockable with central lock. Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility.
Complete with GBP’s interior for the drawers in gray sheet steel or red plastic, to create order and order.
The storage case is mounted in the table stand using suspension profiles, which are ordered separately. Hurtsen can also be screwed directly into a heavy table top (40 mm).
Box division, number x height (mm): 1×50 + 1×100 + 1×150. Maximum load distributed weight for Hurts: 100 kg.
The Hurtsars are equipped with ball-bearing expansions, which provide 100% extensibility. Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order inside the drawers.
Not suitable when the lower shelf is used. The storage case fits all tables in the wide range. The Hurtsen can be locked with a central lock.
The storage basket is used freestanding, with or without a wheel base.
Box division, number x height (mm): 1×50 + 3×100 + 1×150.
The Hurtsen can be locked with a central lock. The Hurtsars are equipped with ball-bearing expansions, which provide 100% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order inside the drawers. Maximum load distributed weight for Hurts: 100 kg.
The wheel base (art. no. 40-550-2001) is ordered separately.
The storage case is mounted in the table stand using suspension profiles, which are ordered separately.
Drawer division, number x height (mm): 1×50 + 1×150. Maximum load distributed weight for Hurts: 100 kg
Hurtsen can also be screwed directly into a heavy table top (40 mm). Not suitable when the lower shelf is used.
The storage case fits all tables in a wide range. The Hurtsen can be locked with a central lock. The Hurtsars are equipped with ball-bearing expansions, which provide 100% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order inside the drawers.
Drawer interior in sheet metal. The interior is made of sheet steel. Three longitudinal and three transverse dividers are supplied for optional placement in the slotted side walls. Suitable for box with telescopic rails item no.
Solid Drawer section intended for placement in shelves with a width of 1000 mm and a depth of 500 mm.
The drawer interior includes: 1 x 214 mm, 5 x 107 mm and 2 x 53 mm width. For each division, 2 partitions are included.
Drawer section with five drawers for the Boltless shelving system. The drawer section is used in combination with doors with a height of 1000 mm and side and back pieces. The drawers have 90% extendability. The following drawers are included: 2 drawers with a height of 100 mm and 3 drawers with a height of 200 mm. Max load/box 70 kg.
V06 is a modern shelving unit with well-balanced colors for a pleasant environment.
Comes complete with:
4 posts with feet, 4 brace plates
1 back cross
5 galvanized shelves with shelf hooks.
Easy to assemble. Available in two heights and four different depths. Capacity 150 kg/shelf, evenly distributed. Meets the SS2241 standard. Perfect addition to your storage shelf, storage shelf, shelf.
V06 is a modern shelving unit with balanced colors for a pleasant environment.
This extension section comes with:
1 tight gable
1 back cross
5 galvanized shelves with shelf hooks.
It is easy to assemble and is placed directly on a starter or add-on section. Capacity 150 kg/shelf, evenly distributed. Meets the SS2241 standard. Perfect addition to your storage shelf, storage shelf, shelf.
Storage box with D x W x H = 96 x 105 x 45 mm
Module boxes – series 30.
The market’s most complete and modern range of storage boxes for efficient storage and handling on shelves in racks, warehouses, storage machines, etc. The range consists of 80 mm high boxes. The series contains two different widths and four different lengths.
Storage box no. 3067 DxWxH (mm) 300x230x150 available in blue and red. The box can be divided with longitudinal and transverse dividers.
Module box no. 3069 DxWxH (mm) 500x230x150. The modular box can be divided with longitudinal and transverse dividers.
Module box no. 3070 DxWxH (mm) 600x230x150. The modular box can be divided with longitudinal and transverse dividers.
Storage tray stackable no. 3071 DxWxH (mm) 500x310x200. The storage tray can be divided with longitudinal dividers, see related products.
Storage tray stackable no. 3072 DxWxH (mm) 500x310x250 in blue design. The storage tray can be divided with longitudinal dividers, see related products.
Stock back stackable no. 3073. The stock back can be divided with longitudinal dividers, see related products.
Storage box stackable no. 3074 DxWxH (mm) 250x148x130 available in blue and red. The storage box can be divided with longitudinal dividers, see related products.
Storage box stackable no. 3075 LxWxH (mm) 170x105x075
Conductive storage box ESD 4016, 5016, 6016 for storing components.
The market’s most complete and modern range of storage boxes for efficient storage and handling on shelves in racks, warehouses, warehouse machines etc. The range consists of 100 mm high boxes. Available in two widths and four different lengths.
List rack for Boltless storage shelf. The stand is delivered as a complete set with an upper and lower part for storing long goods, e.g. threaded rods, profiles and moldings.
Joint spanner holder for five joint spanners. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
TL18 lifting column with lifting height 500 mm, this version is 1-single column with outer profile down.
The TL18 is a heavy-duty, electrically driven lifting column in extruded aluminum for use in workshops and industry. You choose whether you want the outer profile up or down.
Each column is supplied with a recessed floor and top plate (257 x 195 x 8 mm) for safe and stable operation and has a working height of 670 – 1170 mm (without table top).
Lifting speed is 22 mm/sec without load and electronic control box is included, regardless of model. Select the desired control unit, hand or foot control.
The pillars are certified according to standards IEC60601-1, ES60601-1, IEC60601-1-2, UL73 & EMC.
TL3 lifting column with lifting height 700 mm, this edition is 1-single column with outer profile down. TL3 is a strong, electrically driven lifting column in extruded aluminum for use in workshops and industry.
For each column, 2 recessed floor and top plates (257 x 195 x 8 mm) must be ordered for safe and stable operation. The table has a working height of 520 – 1220 mm (without table top).
Lifting speed is 34 mm/sec without load and electronic control box is included, regardless of version. Select the desired control unit, hand or foot control.
Pelarana is certified according to standards IEC60601-1 & EMC.
MaxiStore is a compact storage solution with a full 8-16 m2 of storage space for tools in only 2 m2 of floor space. This form of tool storage is very space-saving. With MaxiStore you get a very good overview of the tools.
The MaxiStore has support wheels at the front and a strong handle, which makes it easy to use.
In addition, the storage solution can be equipped with more tool boards (art. no. 200926-2160) for even more compact storage space. Max number of plates/MaxiStore: 14 pcs.
Complete with our wide range of hooks, which consists of around 50 tool hooks for various purposes.
Extra tool board for MaxiStore for even more compact storage space.
MaxiStore includes four tool plates. In total, you can supplement with a maximum of ten additional plates of this model. Max number of plates/MaxiStore: 14 pcs.
Complete with our wide range of hooks, which consists of around 50 tool hooks for various purposes.
Metal handle for sorting box/bucket ESD 25L
The mobile workbench consists of two drawer units with five drawers each. The drawers are equipped with strong expansions, which provide 110% extensibility. The drawers also have drawer locks and central locking. The worktop consists of a chipboard coated with oak parquet and with a steel edge all around. The workbench is equipped with two swivel castors with brake and two fixed wheels without brake, Ø160 mm.
The kit is used for mounting perforated columns on the extension frame for Ergomulti.
The assembly kit consists of two spring-loaded 4-point nuts, two screws and two washers.
One kit is needed per pillar. The mounting kit is only used when the single section is mounted centrally.
With this assembly kit, you can assemble two V06 shelves with their backs facing each other. Works with all back options, V06 is a modern shelving unit with balanced colors for a pleasant environment. Easy to assemble. Available in two heights and four different depths. Capacity 150 kg/shelf, evenly distributed. Meets the SS2241 standard. Perfect addition to your storage shelf, storage shelf, shelf.
Practical mounting set for use in hanging storage, intended for Boltless storage shelf. The set includes 2 deep angles incl. 4 suspension hooks and 1 hanging rod incl. bracket. The capacity is 50kilo / rod.
Assembly trolley Comb. 4 has plenty of plastic trays, which keep the workplace organized. The trolley has a handle and four castor wheels Ø125 mm, of which two wheels with brakes, to be easily moved.
Assembly trolley Comb. 4 consists of:
1 assembly trolley
48 plastic trays gray
6 suspension strips for plastic trays
All-round riding chair, here with a chrome wheel cross and 50mm wheels, is a smart and robust riding chair adapted to you who do a lot of work while squatting. The chair has a simple, round seat in PU foam with stepless adjustment in seat height 350-470mm.
Below you will find additional equipment.
All-round riding chair with undercarriage and 75 mm wheels, is a smart and robust riding chair adapted to you who do a lot of work while squatting. In the underframe of the chair, you will find 5 practical compartments for storing the things you use most during the course of a working day. The chair has a simple round seat in PU foam with stepless adjustment in seat height 350 – 470 mm.
Below you will find additional equipment.
The All-Round Comfort wheelchair, here with a black undercarriage and 75 mm wheels, is a smart and robust wheelchair adapted to those who do a lot of work while squatting. In the underframe of the chair, you will find 5 practical compartments for storing the things you use most during the course of a working day. The comfort version of the Åkstol All-Round has an angled and classic look on the chair seat in PU foam with stepless adjustment of seat height low 390 – 500 mm, high 500-670 mm.
Below you will find additional equipment.
Riding chair All-round, here with an ergonomic and comfortable backrest, black chassis and 75 mm wheels, is a smart and robust riding chair adapted to you who do a lot of work while squatting. In the underframe of the chair, you will find 5 practical compartments for storing the things you use most during the course of a working day. The chair has a simple, round seat in PU foam with stepless adjustment of the seat height 350 – 470/470-650 mm. This practical industrial chair is suitable for use in the workshop, during assembly work or also in connection with work in schools and preschools.
Below you will find additional equipment.
Riding chair All-round V-matic, here with a black chassis and 75 mm wheels, is a smart and robust riding chair adapted to you who do a lot of work while squatting. In the underframe of the chair, you will find 5 practical compartments for storing the things you use most during the course of a working day. The V-matic chair has a unique seating mechanism that gives you movement in all directions – also called free float. In addition, you of course get stepless adjustment of the seat height: 405 – 535/525-705 mm.
Below you will find additional equipment.
Assembly trolley on wheels for adding modular accessories, e.g. shelf, perforated tool cabinet & workshop board. The height of the assembly trolley refers to measurements from the floor. Complete with hook accessories from GBP’s wide hook range.
The following is included in the Assembly trolley:
Bottom shelf, handle and four castors Ø125 mm, two of which have brakes.
Mop cloth ESD 600mm
Floor mop ESD 600mm
Tool hook Key holder with space for 12 keys in varying sizes. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Galvanized anchoring plate for placement on top and bottom of lifting column TL3.
Superstructure frame intended for work tables ErgoMini and ErgoNomi.
With the help of the extension frame, you can mount GBP’s large extension range. Complete with Perforated pillars and Mounting kit for Perforated pillars, which are mounted on the superstructure frame.
Then continue with accessories such as suspension strips with plastic backs, tool boards and tool hooks, shelves, cutting units or lighting, so that the work table is optimal. Hurtsar can be mounted under the table top. With work tables and other workplace furniture from GBP Ergonomics, we guarantee quality, safety and constant development.
Our products improve both efficiency and ergonomics at your workplace. Feel free to contact us if you have questions about work tables or other workplace equipment.
Add-on frame intended for workbench.
Add-on frame intended for ErgoSingle Workstation. The frame is adapted for c/c 670 mm. With the add-on frame, the ErgoSingle can easily be supplemented with more add-on details.
Extension kit adapted for c/c 670 mm.
The extension kit includes:
2 perforated columns 2000 mm, shelf and suspension strip for plastic trays.
Complete the suspension strip with plastic trays for smart and practical storage.
Basic add-on set for work and packing table with perforated columns 1446 mm, intermediate brace and mounting kit. Fits ErgoMulti.
Complete picking trolley 1655 x 1365 mm. (HxW) The combination consists of: Cutting unit with cutting width 1000 mm 1 shelf 1340 mm 6 shelf dividers / cardboard supports with a height of 200 mm Shaft for corrugated cardboard, bubble wrap, gray paper or similar.
Choose this basic frame as a starting point to design your own roller pack and picking cart. The handle in the picture is optional and must be ordered separately.
Complete trolley 1655 x 1365 mm. (HxW) The combination consists of: Cutting unit with cutting width 1000 mm Shaft for corrugated cardboard, bubble wrap, gray paper or similar.
Complete trolley 1655 x 1365 mm. (HxW) The combination consists of: 4 shelves 1350 mm 10 shelf dividers / cardboard supports with a height of 200 mm 2 shelf dividers/cardboard supports with a height of 400 mm.
Complete electrically adjustable packing table in versions such as scale and belt table.
Table stand is a Table 400 with size 2000 x 800 mm and electrically adjustable working height, including 32 mm gray high-pressure laminate table top.
The table’s maximum load applies to the table with a spread load, the maximum weight of the belt machine is 40 kg, the lifting speed applies to an unloaded table.
The table is equipped with a stable intermediate brace. The table is equipped with a tape machine made by Cyklop model M-Pac 5. The M-Pac 5 is a semi-automatic tape machine. The machine is used to strap various packages with PP strapping.
With the strapping machine, you can choose between different impact tension (for light and durable packages) and torque tension. Welding time and temperature are easy to adjust, making the band machine suitable for a variety of applications. The machine is quiet 57 dB. Under the belt machine is a platform scale, model PV490 from Scandinavien Scale.
The scale has a maximum load of 150 kg, but in this application this maximum weight is limited to 40 kg due to the tape machine, resolution 50g. Display for the scale is placed on the table top.
Perforated tool board for wall mounting. The board is perforated with square holes of 9 x 9 mm and with a hole distance of 38 mm. Complete the tool board with our wide range of hooks, which consists of around 50 hooks for various purposes. Color blue, RAL 5005 or Grey RAL 7024. Dimensions (wxh): 1439×679 mm.
Tool cabinet with dimensions h x w x d = 715 x 870 x 250 mm, for placement in perforated columns (CC 900), at the back edge of work and packing tables, on floor-mounted L- and T-stands, on assembly trolleys or directly on the wall. Necessary mounting details for mounting on the column are included. The tool cabinet is perforated (9mm square hole with CC 38mm) so you can use our tool hooks for efficient storage of tools.
Scale PV490 is a platform scale with a loose instrument. The scale can be used freestanding or mounted in a tabletop for best ergonomics. Price supplement for withdrawals in table tops and weighing pans. The scale is easy to use and has a long service life. It fits all kinds of weighing and has a construction that means the scale can withstand a little tougher handling. Max load 150 kg.
Conductive pick box ESD for storing components. Boxes of the same dimensions are stackable.
Pump Comprimé, spare part, for workshop washers Microclean, Masterclean and Maxiclean from 2006-07.
Pump Comprime kit, replacement pump for appliance washers delivered before July 2006. Replaces the pump type Hanning.
Stop strip in gray aluzinc for table top with 40mm thickness in width 1500 mm. The edge is mounted on the table top to prevent things from falling off the table.
Tool holder (w x h x d) 60 x 35 x 40 mm.Tool holder on a base plate like the rest of the hook range and for placement on a tool board, strip or on perforated panels on cabinets or racks. The holder facilitates the storage of implements and tools with handles both inside and outside where many tools need to be stored in a small area. Supplied in 2-packs.
Cleanser ESD 0,75 L spray
Cleanser ESD 5L
Pipe holder, supplied in 2-packs.
Do you want to build yourself or do you perhaps need to supplement the finished starter and follower sections with Galvanized Back Cross. Here you will find the necessary products to adapt your storage shelf, storage shelf, shelf to your own needs.
Back plate in galvanized steel, height 500mm. The back plate is delivered including the necessary fasteners. Combine different back heights adapted to your Boltless shelf.
Back support for All-round chair.
With LEGOLAS, you are given every opportunity to design exactly the saddle chair you desire. The saddle seat on LEGOLAS is ergonomically and comfortably designed, for active sitting with stimulation of the back and neck? Choose a seat in PU foam for easy cleaning, or a textile you find appealing. Seat height and other accessories must also be adapted to your needs. For the highest version of LEGOLAS, we recommend the use of sliding feet.
Below you will find additional equipment.
Safety pin for locking Boltless shelf beams in the gables. Use 2 safety pins per beam.
Side support for FIFO shelf depth 500 mm
Complete cabinet Lacquered 2100 x 1000 x 300mm.
Complete V06 cabinet consisting of:
2 perforated outer end panels, back plate, door section
5 galvanized shelves.
Perfect addition to your storage shelf, storage shelf, shelf.
The cabinet section is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Complete the hurt with the top plan, when used as a stand-alone hurt.
Hurtsen has a door with dimensions W470 x H630 mm. A shelf is included with the kit. Hurtsen is lockable.
Roller shutter with lockable workshop shutter and rubber mat for the top floor.
Hurtsen’s door dimensions are W470 x H630 mm and a shelf is included.
This combination also includes the following products:
301859 – 1 pc Top plan for workshop equipment
301861 – 1 rubber mat 530 x 660
301862 -1 pc Wheel base on a base plate
301862 – 4 swivel castors, 2 of which with brake, Ø125 mm.
Very flexible aggregate with a total width of 1360 mm for cutting corrugated cardboard, paper, bubble wrap, foam, etc. Cutting width is 1000 mm. The unit is placed on a packing table or in combination with the associated bracket for use on the Flex trolley. Extremely solid cutting blade in hardened steel.
Shelf dividers that fit fixed shelves with a depth of 440 mm, which are part of GBP’s range of workshop cabinets.
The shelf divider is clamped around the shelf at the front and back edges.
Supplied in 2-packs.
Practical Partition with a height of 190 mm, for placement between two Boltless shelves. The partition is delivered in a galvanized version and is adapted for shelves with a capacity of 150 kg.
4.8 x 13mm screw to attach T-post to post base. Use of the screw is not necessary to obtain a certified installation, but it makes assembly easier and allows for possible movement of your boltless storage racks. In addition, it will provide the shelf with tip protection when used together with the floor anchor.
Tool hook Hose shelf for hanging various. cables and hoses, etc. Galvanized. 1 pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Do you want to build yourself or do you perhaps need a plinth for the start and follower sections that are defined as standard? Here you will find the necessary products to adapt your archive shelf or storage shelf to your own needs.
Sockelplåt för fristående verkstadshurts. Sockelplåten behövs för höjdjustering av fristående hurts, när den används tillsammans med Fast Arbetsbänk / Tung benbock. Säljs i 2-pack.
Bucket 25L ESD 395x275x315mm
Spiral grounding cable with 10 mm push button, adapted for connection to ESD bracelets with 7 mm connection.
Build and adapt the workplace for safe and effective dissipation of static electricity. Discharges of static electricity ESD (Electro Static Discharge) cause great damage every year in the electronics industry. It is becoming increasingly important to protect sensitive electronics against ESD damage.
Spiral cable ESD 10 mm button/track. Length 1.8m
Spiral cable ESD 10 mm button/knob. Length 1.8m
Hållare för sprayburkshållare eller liknande. Förzinkad.
Verktygskroken passar perforerade paneler, där den hakas i plåtens perforering och låses med stoppskruv.
Den perforerade panelen (verktygstavlan) har håldimension 9 mm (4-kantshål) och hålavstånd 38 mm.
rokarna passar samtliga perforerade paneler, oavsett om de är monterade i skåp, vagnar eller på arbetsbord.
Strut plate/depth stabilization for T-profile/post.
STINGRAY COMFORT is a comfortable saddle chair including backrest. Both the saddle seat and the back are PU foam for easy cleaning and hard use. The asynchronous mechanism allows the chair to be easily adjusted when in use. Stepless adjustment of the seat, back angle and seat height. Choose the model and equipment that is adapted to your needs. For the highest version of STINGRAY COMFORT we recommend the use of sliding feet.
Below you will find additional equipment.
The STINGRAY V-MATIC is a saddle chair that comes without a backrest, but with the unique V-MATIC seating mechanism. It allows free movement in all directions. Choose a seat in furniture textile, artificial leather or PU foam where hygiene is required. V-MATIC thus provides free movement when the chair is in use. Otherwise, there is of course stepless adjustment of the seat height. Choose the model and equipment that is adapted to your needs. For the highest version of the STINGRAY V-MATIC we recommend the use of sliding feet.
Below you will find additional equipment.
Single post foot in galvanized version, used at the bottom of T-post for the necessary support on the floor.
This pivoting arm has a length of 700 mm and is supplied with 1 eye hook for hanging tools and other mounting equipment. The arm is mounted in our perforated columns, can be swiveled 180 degrees and has a capacity of 10 kg distributed load.
Light gray longitudinal divider, three possible positions in the back. Fits bearing box 3067, 3068, 3069 and 3070. 10-pack
T-profile/post for Boltless storage shelves.
Do you want to build yourself or do you perhaps need to supplement the finished starter and follower sections with Light Gray Tight Back 2100x1000mm. Here you will find the necessary products to adapt your storage shelf, storage shelf, shelf to your own needs.
Tool trolley 2 incl. hooks consist of a tool cabinet made of perforated sheet metal for hanging tools. The cabinet is equipped with square tube legs with four swivel wheels Ø100 mm, one of which is lockable, and a bottom shelf. The cupboard on the tool trolley is prepared for a padlock.
Wire back piece in 3 mm galvanized mesh with mesh width 50 x 50 mm, height 500 mm. The net backs are delivered including the necessary fastening hooks. Combine different back heights adapted to your Boltless shelf.
Tool hook wire shelf 385x180x100 mm. Powder coated in RAL 9006. Supplied in 1-pack
Frame for placement on Boltless shelf. The frame is delivered in galvanized steel and is used with dividers to create practical and functional small parts storage in your Boltless shelving unit. Practical trays in galvanized version for clear storage of small parts. The small parts storage is intended for shelf width 1000 mm and is available for several shelf depths. The height at the rear edge is 200 mm, 100 mm at the front. Complete with desired number of dividers (at least 1 required).
Underframe for GBP’s workshop cabinet with dimensions (WxD) 1020×540 mm.
Undercarriage (truck base) simplifies the work when moving the cabinet. Use a pallet lifter or truck, so you don’t have to empty the cabinet when it has to be moved.
Cross beam intended for use in the Boltless universal shelf.
Light gray transverse divider. Fits storage boxes 3067, 3068, 3069 and 3070. 10-pcs.
HPL undershelf in 24 mm thickness, adapted for work tables with H-stand base and with depth 800 mm and width 1500/2000 mm.
Bottom shelf in 40mm thickness, adapted for work tables with heavy leg braces and depth 800mm / width 1200/1500/2000mm.
Steel shelf with a depth of 350 mm, for installation under a workshop bench with a width of 1200/1500/2000 mm. Maximum load is 100 kg. Powder coated in gray RAL 7004.
Bottom shelf for ErgoMini/ErgoNomi with a width of 2000 mm, is a 24 mm tabletop with a top surface in gray high pressure laminate (HPL) edged with dark gray ABS edging. The capacity is 50 kg distributed load. The lower shelf is delivered complete and brackets for attachment to the ErgoMini/ErgoNomi underframe are included.
Perforated tool bar with 9mm square hole with cc measure 38mm. With the supplied mounting kit, the strip is easily mounted on columns on work tables, on wall rails or on assembly trolleys.
Smooth perforated tool bar, a good help for order and order. Complement the perforated strip with GBP’s wide range of hooks, which consists of around 50 hooks for different purposes.
Suspension eye, which is in a package with 2 eye screws, Ø25 mm, square nut, nut and washer.
The suspension loop is mounted in the suspension C-profile.
Suspension profiles for storage boxes depth 485 mm. The suspension profiles fit motorized work tables type Bord 400 with a depth of 800 mm. Delivered in pairs.
Suspension profiles for storage cases. The suspension profiles fit motorized work tables type ErgoMini 2 and crank tables ErgoNomi with a depth of 800 mm. Delivered in pairs.
Suspension profile for storage boxes. The suspension profiles fit motorized work tables type ErgoMulti with a depth of 800 mm. Delivered in pairs Easy-to-mount suspension profiles for our storage cases, choose the suspension profile according to your choice of your ergonomic work table.
Suspension profiles for storage cases. The suspension profiles fit manually adjustable work tables type light frame with bottom depth 585 mm (table depth 620 mm). Delivered in pairs.
Suspension profiles for storage cases. The suspension profiles fit manually adjustable work tables type light frame with undered depth 765 mm (table depth 800 mm) and for the Single column tables TL18. Delivered in pairs.
Suspension rail with integrated brackets for straight or angled mounting.
The suspension strip is intended for hanging plastic trays in workshop cabinets.
ESD-approved suspension rail, for use with our perforated rails as an addition to our work tables.
Build and adapt the workplace for safe and effective dissipation of static electricity. Discharges of static electricity ESD (Electro Static Discharge) cause great damage every year in the electronics industry. It is becoming increasingly important to protect sensitive electronics against ESD damage.
Suspension rail with a width of 900 mm, for use together with storage boxes or modular boxes. The rail has integrated brackets for straight or angled mounting on our perforated columns. The capacity is 20 kg distributed load. Plastic boxes are not included and must be ordered separately – See related products for the most common plastic boxes used with the suspension rail.
Suspension profiles for workshop cupboards and table drawers depth 605 mm. The suspension profiles fit motorized work tables type Bord 400 with a depth of 800 mm. Delivered in pairs.
Galvanized collection tank with a capacity of 30 l. The tank is h x w x d = 72 x 950 x 650 mm and is intended for placement between the ends of a shelf with a width of 1000 mm.
Pull-out shelf for SMV tool cabinet with width 1000 mm.
Pull-out box for SMV tool cabinet with width 1000 mm.
Pull-out shelf for label printers, or for other purposes. Attaches to shelves 300 or 457 mm deep intended for packing tables with a smooth top and folded edges all around. The shelf has a practical storage compartment at the front for documents and folders in A4 format.
Practical pull-out shelf with size 1000 x 300 mm .. The pull-out shelf comes complete with solid slides (100% pull-out) and attachment to shelf ends.
Practical moldings for filling gaps between shelves in back-to-back shelves. This version is delivered in a galvanized version and is intended for use in Boltless storage shelves with shelf beams.
Platform scale type 6000KD-PS, with a minimum load of 50 g, and a maximum load of 150 kg. Intended for placement directly on the table, or folded into a table top in a weighing tub, item number 436099.
Folding frame intended for the KD6000 platform scale, 436105. Outer dimensions of the tub 333 x 313 mm, Total dimensions 357 x 337 mm. Color RAL 9006
To stabilize the V06 shelves against the wall, we have developed this wall bracket, V06 is a modern shelf rack with balanced colors for a pleasant environment. Easy to assemble. Available in two heights and four different depths. Capacity 150 kg/shelf, evenly distributed. Meets the SS2241 standard. Perfect addition to your storage shelf, storage shelf, shelf.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Box division, number x height (mm): 1×50 + 1×100 + 3×150. Maximum load distributed weight for Hurts: 175 kg.
Complete the hurt with the top plan, when used as a stand-alone hurt. Lockable with central lock.
Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order.
The workshop desk drawer is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top. Complete the hurt with the top plane when used as a free-standing hurt. Lockable with central lock. Built-in safety means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility. Complete with interior decoration for the drawers in gray sheet steel or red plastic to create order and order. Box division, number x height (mm): 1×50 + 1×100 + 3×150. Maximum load distributed weight: 175 kg.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Complete the drawer section with the top plan, when used as a stand-alone hurt. Lockable with central lock.
Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility. Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order.
Drawer division, number x height (mm): 1×50 + 1×100 + 1×150 + 1×300. Maximum load distributed weight for drawer section: 175 kg.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top. Complete the desk drawer section with the top plane when used as a free-standing hurt. Lockable with central lock. Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility. Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order. Box division, number x height (mm): 1×50 + 2×100 + 1×150 + 1×200. Maximum load distributed weight for desk drawer section: 175 kg.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Complete the hurt with top plan when used as a free-standing hurt. Lockable with central lock.
Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order.
Drawer division, number x height (mm): 6×100. Maximum load distributed weight for: 175 kg.
The workshop desk is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top. Complete the hurt with the top plane when used as a free-standing desk. The desk has a door with dimensions W470 x H630 mm. A shelf is included with the kit. The desk is lockable.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Drawer division, number x height (mm): 1×50 + 1×100 + 1×150 + 1×300. Maximum load distributed weight for Hurts: 175 kg.
Complete the hurt with the top plan, when used as a stand-alone hurt. Lockable with central lock.
Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order.
Rolled roof including lockable workshop roof and rubber mat used for the roof. Hurtsen can be locked with a central lock that has built-in security, only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility. Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order. Drawer division, number x height (mm): 1×50 + 1×100 + 1×150 + 1×300. Maximum load distributed weight for Hurts: 175 kg. This combination also includes the following products:
1 top plan for workshop equipment
1 rubber mat 530 x 660
1 wheel base on a base plate
4 swivel castors, 2 of which with brake, Ø125 mm. Maximum load distributed weight for box: 35 kg. Inside box dimensions: 450×605 mm, weight: 56 kg.mm and a shelf is included.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Box division, number x height (mm): 1×50 + 2×100 + 1×150 + 1×200. Maximum load distributed weight for Hurts: 175 kg.
Complete the hurt with the top plan, when used as a stand-alone hurt. Lockable with central lock.
Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility.
Complete with interior decoration for the drawers in gray sheet steel or red plastic, to create order and order.
The workshop chair is used as a stand-alone chair or together with a table stand Heavy leg stand and a table top.
Drawer division, number x height (mm): 6×100. Maximum load distributed weight for Hurts: 175 kg.
Complete the hurt with the top plan, when used as a stand-alone hurt.
Lockable with central lock. Built-in safety, which means that only one drawer can be pulled out at a time. The Hurtsen is equipped with ball-bearing expansions, which provide 110% extensibility.
Brace hook for various pliers or similar gripping tools. Galvanized. The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw. The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm. Delivered in 3-packs.
Single hook for hanging e.g. hand tools. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Sold in packs of 5 and available in lengths of 10 mm or 50 mm.
Spring clamp Ø6, 12, 18 and 25 mm for hanging e.g. screwdrivers or similar small hand tools. Supplied in 5-packs.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Galvanized packaging hook is adapted for hanging different packages with riders. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Socket holder for five sockets. Galvanized. The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The box holder is adapted for hanging small storage boxes/plastic trays. Complete with plastic backing from GBP. The holder is galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Galvanized hook for hanging spanners. Comes in 5-packs.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Galvanized ring hook. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Ring key strip, with space for seven ring keys, which can also be used as a sleeve holder. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Roll holder adapted for hanging different rolls. Supplied in 1-pack.
Round hook for hanging hand tools and smaller hand machines. Galvanized. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Screwdriver holder.
Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Closed double hook for hanging e.g. small hand tools. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Double hook for hanging e.g. hammer or similar impact tool. Galvanized.
Available in different sizes, see article number below.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Double hook for hanging e.g. hammer or similar impact tool. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Galvanized single hook for hanging e.g. hand tools. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Double hook adapted for hanging hammers and similar impact tools. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Galvanized single hook at a 30° angle, for hanging e.g. hand tools. 5-pack.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
The perforated panel (tool board) has hole dimension 9 mm (4-edge hole) and hole spacing 38 mm.
The hooks fit all perforated panels, regardless of whether they are mounted in cabinets, trolleys or on work tables.
Single hook at a 30° angle, for hanging e.g. hand tools. Galvanized.
The tool hook fits perforated panels, where it is hooked into the sheet perforation and locked with a stop screw.
Perforated panel, door panel for tall workshop cabinet.
The panel is mounted on the inside of the right door. Fittings included.
A maximum of two panels per cabinet can be installed.
Perforated panel, a side panel, supplied with suspension fittings for mounting on the perforated rails in the sides of the workshop cabinet.
The perforated panel is supplied in pairs.
Tool cabinet with dimensions h x w x d = 475 x 870 x 120 mm, for placement in perforated columns (CC 900), at the back edge of work and packing tables, on floor-mounted L- and T-stands, on assembly trolleys or directly on the wall. Necessary mounting details for mounting on the column are included. The tool cabinet is perforated (9mm square hole with CC 38mm) so you can use our tool hooks for efficient storage of tools.
Tool cabinets for placement directly on the wall or in perforated columns (CC 900), at the back edge of work and packing tables, on floor-mounted L- and T-stands, on assembly trolleys. Necessary mounting details for mounting on the column are included.
The tool cabinet is perforated (9mm square hole with CC 38mm) so you can use our tool hooks for efficient storage of tools.
Perforated tool board with 9mm square hole with cc measure 38mm.
With the included mounting kit, the board is easily mounted on columns on work tables, on wall rails or on mounting trolleys. The painting can also be mounted right on the wall.
Workshop board suitable SMV tool cabinet with depth 435 mm. The board is easily mounted on the inside of the cabinet door.
The board is perforated with square holes of 9 x 9 mm and with a hole distance of 38 mm.
Perforated tool board for wall mounting. The board is perforated with square holes of 9 x 9 mm and with a hole distance of 38 mm. Complete the tool board with our wide range of hooks, which consists of around 50 hooks for various purposes. Color grey RAL 7024 or blue RAL 5005. Dimensions 1950×950 mm.
Workshop board suitable SMV tool cabinet with depth 435 mm. The board is easily mounted at the back (back) inside the cabinet.
The board is perforated with square holes of 9 x 9 mm and with a hole height of 38 mm.
Tool trolley 2 incl. hooks consist of a tool cabinet made of perforated sheet metal for hanging tools. The cabinet is equipped with square tube legs with four swivel wheels Ø100 mm, one of which is lockable, and a bottom shelf. Tool hooks for around 100 hand tools are included. The cupboard on the tool trolley is prepared for a padlock.
A strong tool cart with lacquered wooden top in beech and steel edge around the table top. The tool trolley is equipped with a cabinet section with a removable shelf and five pull-out drawers. The trolley has a cylinder lock for both cupboards and drawers. Two fixed and two swivel castors, Ø120mm, of which the swivel castors have a brake. Inside dimensions of drawers (WxDxH mm): 370 x 515 x 90/205. Door dimensions (WxH mm): 400 x 680. As accessories, there are tool hooks, pillars, plastic boxes with box strips and tool hooks.
This tool cart has a lacquered wooden plate with a steel edge around its entire worktop. The cart consists of 2×5 100% pull-out drawers. Supplied with cylinder locks for both cupboards and drawers. Two fixed and two swiveling wheels, the swiveling ones have a brake.
A motorized CE-marked tilting table with a single-column stand, the work surface can be tilted up to 75º. The working surface can be extended by 315 mm by moving the cutting edge.
The edge of the race can function as support or as a shelf for tools, but the goods on the table MUST be screwed into the table frame or into the table top.
Regulation of working height and angulation takes place with hand controls located on the right or left side of the stand. The angling table is intended as an ergonomic and rational assembly table.
All the steel parts of the table stand are fully welded and the table is very stable. The table is delivered fully assembled and functionally tested. delivered on a EUR pallet. Excl. table top. Wheel set is available as an accessory.
A complete motor-driven CE-marked tilting table with a single-column stand, the work surface can be tilted up to 75º.
The working surface can be extended by 315 mm by moving the cutting edge. The edge of the race can function as support or as a shelf for tools, but the goods on the table MUST be screwed into the table frame or into the table top.
Regulation of working height and angulation takes place with hand controls located on the right or left side of the stand. The angling table is intended as an ergonomic and rational assembly table. All the steel parts of the table stand are fully welded and the table is very stable.
The table is delivered fully assembled and functionally tested and is delivered on a EUR pallet. Excl. table top. Wheel set is available as an accessory.
A motorized CE-marked tilting table with two-column stand, the work surface can be tilted up to 75º. The working surface can be extended by 315 mm by moving the cutting edge. The edge of the race can function as support or as a shelf for tools, but the goods on the table MUST be screwed into the table frame or into the table top. Regulation of working height and angulation takes place with hand controls located on the right or left side of the stand. The angling table is intended as an ergonomic and rational assembly table. All the steel parts of the table stand are fully welded and the table is very stable. The table is delivered fully assembled and functionally tested, delivered on a EUR pallet. Excl. table top. Wheel set is available as an accessory.
A complete motor-driven, CE-marked tilting table with two-column stand, the work surface can be tilted up to 75º.
The working surface can be extended by 315 mm by moving the cutting edge. The edge of the race can function as support or as a shelf for tools, but the goods on the table MUST be screwed into the table frame or into the table top.
Regulation of working height and angulation takes place with hand controls located on the right or left side of the stand. The angling table is intended as an ergonomic and rational assembly table. All the steel parts of the table stand are fully welded and the table is very stable.
The table is delivered fully assembled and functionally tested, delivered on a EUR pallet. Including assembled plywood table top. Wheel set is available as an accessory.
Wheel set for work table ErgoMulti and Bord 400 is complete and consists of 4 double wheels, lockable castors with Ø75mm diam. Height 99 mm, bolt diameter 10 mm.
Outer gable with a height of 1000, which is delivered in a powder-coated version.
Do you want to build it yourself or do you perhaps need to supplement the finished starter and follower sections with dark gray gables. Here you will find the necessary products to adapt your storage shelf, storage shelf, shelf to your own needs.
Box rack consisting of a V-06 storage shelf with a height of 2100 mm (capacity 150 kg).
The shelf comes with blue storage trays with W x H = 230 x 100 mm and/or blue small storage trays with W x H = 115 x 100 mm.